Technical training. Product information. F80/F82 Complete Vehicle BMW Service Edited for the U.S. market by: BMW Group University Technical Training ST1402 6/1/2014 General information Symbols used The following symbol/schematic diagram is used in this document to facilitate better comprehension or to highlight very important information: A Contains important safety information and information that needs to be observed strictly in order to guarantee the smooth operation of the system. Information status and national-market versions BMW Group vehicles meet the requirements of the highest safety and quality standards. Changes in requirements for environmental protection, customer benefits and design render necessary continuous development of systems and components. Consequently, there may be discrepancies between the contents of this document and the vehicles available in the training course. This document basically relates to the European version of left-hand drive vehicles. Some operating elements or components are arranged differently in right-hand drive vehicles than shown in the graphics in this document. Further differences may arise as a result of the equipment specification in specific markets or countries. Additional sources of information Further information on the individual topics can be found in the following: • Owner's Manual • Integrated Service Technical Application. Contact: conceptinfo@bmw.de ©2014 BMW AG, Munich Reprints of this publication or its parts require the written approval of BMW AG, Munich The information contained in this document forms an integral part of the technical training of the BMW Group and is intended for the trainer and participants in the seminar. Refer to the latest relevant information systems of the BMW Group for any changes/additions to the technical data. Information status: March 2014 BV-72/Technical Training F80/F82 Complete Vehicle Contents 1. Introduction.1 1.1. M history.2 1.1.1. E30 M3.2 1.1.2. E36 M3.4 1.1.3. E46 M3.6 1.1.4. E90/E92/E93 M3.8 1.2. F80 M3 vehicle profile.10 1.3. F82 M4 Coupe vehicle profile.11 2. Technical Data.13 2.1. Garage dimensions.13 2.2. Comparison of technical data in BMW.14 2.2.1. BMW EfficientDynamics measures.16 2.3. BMW M3 and M4 Coupe compared to competitors.17 2.3.1. M3.17 2.3.2. M4 Coupe.18 3. Body.19 3.1. Bodyshell.19 3.1.1. Chassis and suspension components and rigidity concept.19 3.2. Exterior.21 3.2.1. Front view.21 3.2.2. Side view.23 3.2.3. Rear fender and rear view.27 3.2.4. Trunk lid.28 3.2.5. Underbody and thermal protection.29 3.3. Interior.30 3.3.1. Driving area and steering wheel.30 3.3.2. Leather trim.31 3.3.3. Seats.32 3.3.4. Doors and decorative strips.33 4. Powertrain.34 4.1. Engine S55B30T0.34 4.2. Transmission.34 4.2.1. Manual gearbox.34 4.2.2. Clutch.36 4.2.3. M double-clutch transmission (M DCT) with Drivelogic.36 4.2.4. Structure and power flow.38 4.2.5. Technical data of M DCT.43 4.2.6. System information.44 F80/F82 Complete Vehicle Contents 4.2.7. M gear selector switch.47 4.2.8. Drivelogic.47 4.2.9. Launch Control.48 4.2.10. Transmission control unit.49 4.2.11. Emergency gearbox release.49 4.2.12. Service information.50 4.3. Driveshaft.51 4.3.1. Service information.52 4.4. Rear axle final drive.52 4.4.1. Active M Differential.52 4.4.2. Structure/Function.54 4.4.3. System information.57 4.4.4. Service information.60 4.4.5. Half-shafts.61 4.4.6. Wheel flange.61 5. Chassis and Suspension.63 5.1. Front Axle.64 5.1.1. Steering.67 5.1.2. Servotronic.69 5.1.3. Steering angle sensor.70 5.1.4. System wiring diagram, M Servotronic (EPS).71 5.2. Rear axle.72 5.3. Brakes and wheels/tires.75 5.3.1. Brakes.75 5.3.2. Wheels/tires.79 5.4. Dynamic handling control systems.80 5.4.1. Vertical Dynamics Management.80 5.4.2. Transverse dynamics management.85 5.4.3. Longitudinal dynamics management.85 6. General Vehicle Electronics.86 6.1. Voltage supply.86 6.1.1. Overview.86 6.1.2. Advantages.86 6.1.3. Comparison of li-ion starter battery/lead starter battery.87 6.1.4. Structure of the li-ion starter battery.88 6.1.5. Function.90 6.1.6. Actions in the event of a fault.91 6.1.7. System wiring diagram.94 F80/F82 Complete Vehicle Contents 6.1.8. Li-ion starter battery in Service.95 6.2. Bus overview.97 6.3. On-board information.100 6.3.1. MDrive menu.100 6.3.2. M instrument cluster.104 6.3.3. Head-Up Display.105 6.3.4. Active Sound Design.105 6.3.5. M Lap Timer app.106 7. Brief Overview of Equipment.107 7.1. F80/F82 standard equipment.107 7.1.1. Paint colors.107 7.1.2. Leather colors.108 7.1.3. Interior trims.108 F80/F82 Complete Vehicle 1. Introduction The BMW M brand is expanding. In addition to the current BMW M models (the 5-Series, 6-Series and X models), for the first time there is also a BMW M4 Coupe with the introduction of the fifth generation of the new BMW M3 . Similar to all BMW AG vehicles, the BMW M Coupe and the M Convertible body variants will also be marketed as a BMW 4-Series in order to clearly distinguish this segment from the Sedans. The "4" in the type plate is a visual indicator of how different the new BMW M4 Coupe is to the BMW M3 4 door Sedan with its own personality, enhanced sporting character and more exclusivity. The new BMW M4 Coupe and the new BMW M3 in the fifth generation were systematically designed for lightweight construction. In order to achieve this objective, this lightweight construction concept was consistently applied in the body area, as well as in the powertrain and chassis and suspension. A composite construction with different material combinations is used in the body, electrical system, in the chassis and suspension and the powertrain. Metals such as steel, magnesium and aluminum, as well as the use of plastics and fiber composites, are used alternately. In contrast to the predecessor where a high-speed 8-cylinder naturally aspirated engine was used, for the first time in the BMW M3/M4 Coupe an engine with six cylinders and turbocharging is used as a powertrain. In the area of the powertrain concept, the BMW M3 and the BMW M4 Coupe thus pursue the same strategy as their big brother in the BMW M X-Series, as well as that of the BMW M5/M6, where turbocharged engines have been in use for a long time. This combination of consistent lightweight construction and turbocharging guarantees that power and agility are exceptional and enhances the competitive position of the BMW M3 and BMW M4 Coupe. With success embedded in the genes, the new BMW M4 Coupe and the new BMW M3 in the fifth generation will celebrate their global premier in June 2014. 1 F80/F82 Complete Vehicle 1. Introduction 1.1. M history 1.1.1. E30 M3 It all started with the first M3, launched as a thoroughbred sports car for the road. Roughly 18,000 vehicles, Coupe and Convertible. Two four-cylinder four-valve engines were available worldwide. It was produced between 1986 -1991 (1988 -1991 in the US market), the first M3 generation turned the world of racing upside down. The original M3 also showed its sporting ambitions in its exterior design. The flared wheel arches and a large rear spoiler gave it a massive road presence. E30 M3 1986 The E30 M3 celebrates its debut with a 4-cylinder engine (SI 4B23) and 194/200 HP with/without catalytic converter. 1987 The M3 dominates the touring car races worldwide. Roberto Ravaglia brings the championship title back to Munich. The limited edition Evo I with 200 HP (SI 4B23) is here. 1988 The popular Evo II now has 220 HP (S14B23). Those who like to go "topless" can choose the M3 convertible. 2 F80/F82 Complete Vehicle 1. Introduction 1989 The M3 wins 16 national and European titles, including the European Hill-Climbing Championship for Touring Cars. The special edition Cecotto with 215 HP (SI 4B23) makes its debut. E30 M3 Cecotto 1990 The M3 wins 15 national and international championships. The limited quantity of the Evo II with catalytic converter and 238 HP (S14B25) is sold out quickly. 3 F80/F82 Complete Vehicle 1. Introduction 1.1.2. E36 M3 Over 70,000 vehicles, Coupe, Convertible and 4 door Sedan are mass produced. The Z3 M Roadster and Z3 M Coupe are not included. There was the M3 with two different engines and vehicle versions, a US version and a European version. In the US market it was produced in two versions the first in 1995 and the later between 1996-2000. The second-generation M3 was offered as a complete model series. First came the Coupe and two years later the Convertible and Sedan. And the engine received a nice boost, too: The four-valve six-cylinder engine delivered 240 hp. E36 M3 as 4 door Sedan, Coupe and convertible 1992 The second M3 generation, the E36 M3 with a 6-cylinder engine and 286 HP (S50B30/US S52B30 with 240 HP), attracts a great deal of attention, the individual version celebrates its global premiere at the Geneva Motor Show. For the first time, the high pressure VANOS (single VANOS) is used in a M engine. 1993 The E36 M3 is now also available as a convertible. 1994 Steve Soper, Joachim Winkelhock and Jonny Cecotto win the touring car world championship title. For the first time, a 4-door Sedan is also offered with the E36 M3. The type approval series of the M3 GT (only Coupe) which has 295 HP (S50B30) is developed. 4 F80/F82 Complete Vehicle 1. Introduction 1995 The E36 M3 in the European version has been completely revised. It now has, for example, a compound brake with brake discs made from a combination of materials and a high pressure double VANOS, whereby the engine (S50B32) develops 321 HP. (US version S52B32 still with 240 HP). It is only offered as a Coupe and convertible. 1996 The E36 M3 is available with a sequential M gearbox (SMG I). 5 F80/F82 Complete Vehicle 1. Introduction 1.1.3. E46 M3 The E46 M3 was available in a Coupe and Convertible version. Over 80,000 vehicles were produced. There was one engine worldwide. In the US market it was produced between 2001 and 2006, the third generation of the M3 enters the stage with the M3 Coupe and the high-reving naturally aspirated S54 engine delivering 333 hp at up to 7,900 rpm. BMW once more introduced a true sports car, which, like its predecessor, was crowned “best handling car”. From 2001, BMW added the convertible version. E46 M3 2000 The third generation, the E46 M3, has a 6-cylinder engine with a high-speed concept and 343 HP (S54B32). This first M engine with "high-speed concept" impresses the experts and is awarded "Engine of the Year". The M3 is the first M vehicle to receive the fully variable M differential lock with up to 100 percent locking action as standard. 2001 The M3 convertible combines the fascination of the M power with "topless" driving pleasure. The sequential M gearbox of the second generation (SMG II) is available. 6 €191 F80/F82 Complete Vehicle 1. Introduction 2002 With the M3 CSL with 360 HP (S54B32HP), the BMW M shows how a high-powered vehicle can be further enhanced through the use of lightweight construction materials in an intelligent lightweight construction. For the first time, the M track mode (today called M dynamic mode), the SMG launch control (automatic upshift in S mode shortly before maximum speed) and an oil level check are used. E46 M3 CSL 7 F80/F82 Complete Vehicle 1. Introduction 1.1.4. E90/E92/E93 M3 The Coupe was launched in 2007, followed by the 4 door Sedan and convertible with about 70,000 vehicles produced up until January 2014. The E9x BMW M3 had a FI inspired naturally aspirated V8 engine, suspension and drivetrain, a convincing design and best-in-class performance, the latest generation of the BMW M3 is once again making headlines. As with all M vehicles, BMW delivers a true sports car with fantastic everyday usability. The forth generation BMW M3 was available across the E9X model line up, as E92 Coupe, E90 Sedan or as a Convertible with the E93. This M3 features the successor of SMG III the M-DCT (M Double-Clutch Transmission with Drivelogic). E92 M3 2007 The fourth generation of the M3 comes in 2007 as a Coupe E92 and at the end of 2007 as a Sedan E90 with the high-speed S65B40 engine with 420 HP (414 HP and 295 Ib-ft in the US). 2008 The E93 M3 (convertible version) was introduced . For the first time in the history of BMW, a M DKG (M-DCT I) is also used, which allows a gear change without tensile force interruption and replaces the sequential M gearbox. Over a quarter of a century and five generations of BMW M3: The sportiest 3-Series as E9x celebrated its 25th birthday in 2010. 8 F80/F82 Complete Vehicle 1. Introduction 2010 As low volume production for customers who take part in club sport events, BMW M GmbH offers the M3 GTS. The sporty vehicle underwent modifications in the powertrain and chassis and suspension, as well as in the interior equipment and the body, in order to meet the requirements in club sports. The power of the high-speed S65B44 was raised to 450 HP. This vehicle was not available in the US market. E92 M3 GTS 9 TGI 00269 F80/F82 Complete Vehicle 1. Introduction 1.2. F80 M3 vehicle profile F80 M3 Design and aerodynamics: Four-door high-speed Sedan with M-specific characteristics. Consistent lightweight construction in the entire body with clever aerodynamic design at the front, side and rear areas as well as in the vehicle underbody. Engine/Transmission: 3-liter 6-cylinder engine Turbo-Valvetronic direct injection engine. Enhanced efficiency, while delivering even more power than the previous engine with regard to spontaneous linear power development. Choice of three engine dynamics control programs. Electronically controlled M rear-axle differential lock is standard equipment. The M Double-clutch Transmission with Drivelogic (M DTC) is available as an option. The consistent lightweight construction concept also extends to the design of the powertrain. Engine sound: Adds a Sporty character in the lower and upper engine speed and power range. Active Sound Design (ASD), in conjunction with the original sound, makes the engine sound in the passenger compartment a desired overall experience . Steering: Is direct and precise, with variable M Servotronic (EPS) with Servotronic support (in three stages). M steering wheel with the M shift paddles includes two freely programmable MDrive buttons. 10 F80/F82 Complete Vehicle 1. Introduction • Chassis and suspension/Chassis and suspension dynamics design: M sports suspension is available as optional equipment, selectable driving dynamics programs from comfort to sporty in three stages. Optimal driving precision and adapted interplay of steering, tires, suspension and damping action according to the selected program mode. Dynamic Stability Control (DSC) with M dynamic mode instead of Dynamic Traction Control (DTC). • Seating comfort: Lightweight construction M seats (bucket seats). • Ergonomics of interior equipment: M instrument cluster, MDrive menu, M seats, M-specific decorative strips, M driver footrests and door sill cover strips. • BMW ConnectedDrive assistance systems and mobility services from the BMW ConnectedDrive scope, color Head-Up Display with M-specific scope, Professional Navigation system (SA609), M Lap Timer app. 1.3. F82 M4 Coupe vehicle profile F82 M4 Coupe 11 : F80/F82 Complete Vehicle 1. Introduction • Design and aerodynamics: The two-door high-speed sport Coupe has M-specific characteristics all around. Clever aerodynamic design of the front, side and rear sections as well as the vehicle underbody. The consistent lightweight construction is extended to the entire body. • Engine/Transmission: 3-liter 6-cylinder engine Turbo-Valvetronic direct injection engine. Enhanced efficiency, while delivering even more power than the previous engine with regard to spontaneous linear power development. Choice of three engine dynamics control programs. Electronically controlled M rear-axle differential lock is standard equipment. The M Double-clutch Transmission with Drivelogic (M DTC) is available as an option. The consistent lightweight construction concept also extends to the design of the powertrain. • Engine sound: Adds a Sporty character in the lower and upper engine speed and power range. Active Sound Design (ASD), in conjunction with the original sound, makes the engine sound in the passenger compartment a desired overall experience. • Steering: Is direct and precise, with variable M Servotronic (EPS) with Servotronic support (in three stages). M steering wheel with the M shift paddles includes two freely programmable MDrive buttons. • Chassis and suspension/Chassis and suspension dynamics design: M sports suspension is available as optional equipment, selectable driving dynamics programs from comfort to sporty in three stages. Optimal driving precision and adapted interplay of steering, tires, suspension and damping action according to the selected program mode. Dynamic Stability Control (DSC) with M dynamic mode instead of Dynamic Traction Control (DTC). • Seating comfort: Lightweight construction M seats (bucket seats). • Ergonomics of interior equipment: M instrument cluster, MDrive menu, M seats, M-specific decorative strips, M driver footrests and door sill cover strips. • BMW ConnectedDrive assistance systems and mobility services from the BMW ConnectedDrive scope, color Head-Up Display with M-specific scope, Professional Navigation system (SA609), M Lap Timer app. 12 F80/F82 Complete Vehicle 2. Technical Data 2.1. Garage dimensions M3 Index Explanation e 1424 mm b 1579 mm c 1877 mm d 811 mm e 2812 mm f 1048 mm e 4671 mm h 1603 mm i 2037 mm M4 Coupe 13 F80/F82 Complete Vehicle 2. Technical Data Index Explanation e 1383 mm b 1579 mm c 1870 mm d 811 mm e 2812 mm f 1048 mm e 4671 mm h 1603 mm i 2014 mm 2.2. Comparison of technical data in BMW M3 Designation Unit E90 M3 F10M5 F80 M3 Engine series S65B40 S63B44T0 S55B30T0 Engine control MS S60 MEVD 17.2.8 MEVD17.2.G Transmission type GS7D36SG GS7D36BG GS7D36BG designation MDCT MDCT MDCT Length [mm] 4580 4910 4671 Width [mm] 1817 1891 1877 Height [mm] 1447 1456 1424 Number of seats 5 5 5 Luggage compartment volume [1] 450 520 480 Max. speed [km/h/mph] 250*/155* 250*/155* 250*/155* Acceleration 0-60 mph [s] 4.6 4.2 4.1 1,000 m, stationary start [s] 23.3 21.9 21.9 Rolling acceleration 50-75 mph, 4th/5th gear [s] 4.4/5.4 3.7/4.6 3.5/4.3 Nominal engine power [kW/bhp] 309/414 412/560*** 317/425 at engine speed [rpm] 8300 6000-7000 5500-7300 Power-to-weight ratio (DIN) [kg/kW] 5.3 4.5 4.9 Torque at speed [Nm/lb-ft] 400/295 680/500 550/406 [rpm] 3900 1500-5750 1850-5500 14 F80/F82 Complete Vehicle 2. Technical Data Designation Unit E90 M3 F10M5 F80 M3 Aerodynamics: c x (drag coefficient) 0,31 0,33 0,34 A (area) [m 2 ] 2,23 2,40 2,29 c x x A(drag) [m 2 ] 0,69 0,79 0,78 Curb weight Euro *** [kg] 1700 1945 1635 DIN [kg] 1625 1870 1560 Rear axle load section, empty (DIN) [%] 48.8 47.1 47.9 Load capacity [kg] 525 540 540 Permissible gross weight [kg] 2150 2410 2100 Fuel consumption [1/100 km] 112 9.9 8.3 Fuel tank capacity [1] 63 80 60 CO 2 emissions [grams per kilometer] 263 232 194 Exhaust emission standards LEV II ULEVII ULEVII * electronically regulated; vehicles with M DCT are 0.2 s faster 0-60 mph. M4 Coupe Designation Unit E92 M3 F82 M4 Coupe Engine series S65B40 S55B30T0 Engine control MSS60 MEVD17.2.G Transmission type designation GS7D36SG M DCT GS7D36BG M DCT Length [mm] 4615 4671 Width [mm] 1804 1870 Height [mm] 1424 1383 Number of seats 4 4 Luggage compartment volume [1] 430 445 Max. speed [km/h/mph] 250*/155* 250*7155* Acceleration 0-60 mph [s] 4.5 4.1 1,000 m, stationary start [s] 22.9 21.9 Rolling acceleration 50-75 [s] 4.2/5.2 3.5/4.3 mph, 4th/5th gear 15 F80/F82 Complete Vehicle 2. Technical Data Designation Unit E92 M3 F82 M4 Coupe Nominal engine power [kW/bhp] 309/414 317/425 at engine speed [rpm] 8300 5500-7300 Power-to-weight ratio (DIN) [kg/kW] 5.2 4.8 Torque at speed [Nm] 400 550 [rpm] 3900 1850-5500 Aerodynamics: c x (drag coefficient) 0,31 0,34 A (area) [m 2 ] 2,17 2,23 c x x A(drag) [m 2 ] 0.67 0,76 Curb weight Euro *** [kg] 1675 1612 DIN [kg] 1600 1537 Rear axle load section, empty (DIN) [%] 48,3 47,5 Load capacity [kg] 480 503 Permissible gross weight [kg] 2080 2040 Fuel consumption [1/100 km] 11.2 8.3 Fuel tank capacity [1] 63 60 CO 2 emissions [grams per kilometer] 263 194 Exhaust emission standards LEV II ULEVII * electronically regulated; vehicles with M DCT are 0.2 s faster 0-60 mph. 2.2.1. BMW EfficientDynamics measures • TwinPower Turbo Technology. • Gasoline direct fuel injection with Valvetronic. • Automatic engine start-stop function. • Consistent, intelligent lightweight construction through the use of carbon, aluminum and magnesium. • 7-speed M DCT with Drivelogic/efficient 6-speed manual gearbox. • M Servotronic (EPS). • Shift point Display. • Use of ancillary components as required (air conditioning compressor). • Li-ion battery (for the improvement of the brake energy regeneration-lightweight construction concept). • Brake energy regeneration. 16 F80/F82 Complete Vehicle 2. Technical Data 2.3. BMW M3 and M4 Coupe compared to competitors 2.3.1. M3 Designation Unit F80 M3 Mercedes C63AMG Engine series ln-line/6 V /8 Capacity [cm 3 ] 2979 6208 Nominal engine power [kW/bhp] 317/425 336/457 at engine speed [rpm] 5500-7300 6800 Torque at speed [Nm] 550 600 [rpm] 1850-5500 5000 Acceleration 0-60 mph [s] 3.9***/4.1 4.4 Max. speed [km/h] 250*/280** 250*/280** Fuel consumption [1/100 km] 8.3***/8.8 12 CO 2 emissions [grams per kilometer] 'l94***/204 280 Length [mm] 4671 4702 Width [mm] 1877 1770 Height [mm] 1424 1433 Wheelbase [mm] 2812 2760 Luggage compartment volume [1] 480 475 Curb weight US [kg] 1631***/1606 1730 * electronically regulated; ** electronically regulated in conjunction with SA 7ME M Drivers Package; *** M DCT 17 F80/F82 Complete Vehicle 2. Technical Data 2.3.2. M4 Coupe Designation Unit M4 Coupe Audi RS 5 Coupe Mercedes C 63 AMG Coupe Engine series ln-line/6 V/8 V/8 Capacity [cm3] 2979 4163 6208 Nominal engine power [kW/bhp] 317/431 331/450 336/457 at engine speed [rpm] 5500-7300 8250 6800 Torque at speed [Nm] 550 430 600 [rpm] 1850-5500 4000-6000 5000 Acceleration 0-60 mph [s] 3.9***/4.1 4.5 4.4 Max. speed [km/h] 250*/280** 250*/280** 250*/280** Fuel consumption [1/100 km] 8.3***/8.8 10.5 12 CO 2 emissions [grams per kilometer] -194***1204 246 280 Length [mm] 4671 4649 4707 Width [mm] 1870 1860 1795 Height [mm] 1383 1366 1391 Wheelbase [mm] 2812 2751 2760 Luggage compartment volume [1] 445 455 450 Curb weight US [kg] 1626***/ 1601 1790 1730 * electronically regulated; ** electronically regulated in conjunction with SA 7ME M Drivers Package (not in US); *** M DCT 18 F80/F82 Complete Vehicle 3. Body 3.1. Bodyshell 3.1.1. Chassis and suspension components and rigidity concept Front area of vehicle The following measures were implemented in the front section of the vehicle for the connection of the chassis and suspension components and to increase the vehicle rigidity: • Screw connection of the steel brace strut extensions and F80/F82-specific mounting points at the A-pillar and in the area of the spring strut dome. • Carbon brace strut • Front axle support • Stiffening plate • Front-end reinforcements of the engine support made from aluminum behind the cooling module. •r Measures in the front area Index Explanation 1 Carbon brace strut 2 Brace strut extensions 3 Stiffening plate 4 Front axle support 5 Reinforcement in the front section of the vehicle 19 F80/F82 Complete Vehicle 3. Body Rear area of the vehicle The following measures were implemented in the rear section of the vehicle for the connection of the chassis and suspension components and to increase the vehicle rigidity: • Direct screw connection of the rear axle support to the body without the use of rubber mounts. • Additional struts from the rear axle support to the tunnel and side sill unit. Measures in the rear area Index Explanation 1 Tunnel-side sill area struts 2 Rear axle support A Details can be found in the information and specifications of the documents in the Integrated Service Technical Application (ISTA). 20 F80/F82 Complete Vehicle 3. Body 3.2. Exterior 3.2.1. Front view Bumper, front The bumper panel in the M-specific design has flaps at the bottom for reducing the drive at the front axle. It is painted in the vehicle color, including the PDC sensors. Due to the necessary air inlets no fog lights are offered. The frame and the double-bridge longitudinal bars of the kidney grill of the BMW M radiator grill are standard high-gloss black struts for the M3/M4 Coupe and have the M3/M4 Coupe model designation. The optional Side View camera and the Parking Maneuvering Assistant (PMA) sensor is integrated at the side similar to the F3x production vehicle. In addition, the Air Curtain was integrated in the front bumper panel and the neighboring wheel arch panel. The Air Curtain, together with the side gill form part of the integrated Air Breather function. The underbody panels, a rear spoiler and the exterior mirrors, contribute to the aerodynamics concept of the new M3/M4 Coupe. The ornamental grills at the bottom are black-grained. F82 M4 Coupe, front view Headlights The front headlights are adopted from the F32/F33. They were adapted to their position and the front of the M3/F80 was adapted to the headlight shape and position. 21 F80/F82 Complete Vehicle 3. Body Engine compartment lid In contrast to the F3x M3, the engine compartment lid for the F80/F82 is made from aluminum. Six struts were fitted in the middle section to reinforce the engine compartment lid. The supporting inner structure, as well as the outer skin of the engine compartment lid, are made from aluminum. The sound insulation in the passenger compartment of the engine compartment lid is deleted. The typical M "power dome" is functional. It provides the space for the indirect charge air cooling for the S55B30T0 engine. These measures result in weight savings of about 8 kg in comparison to the F3x M3. Front end and air ducts The air intake duct and the intake silencer, as well as their position, are also new. F80/F82 air intake duct and indirect charge air cooler There is a new air duct both for the center radiator package and for the upper low-temperature radiator and the two radiators in the wheel arches. For rigidity reasons the lower engine compartment shield is a one-piece design. It includes the air duct of the horizontal engine oil cooler and optimizes its flow. The lower bumper support comprises a plastic component which saves on weight and is secured to the M3/M4 Coupe deformation elements. The shaped element in the upper bumper support is adapted to the shape of the M3/M4 Coupe bumper panel. The low design of the front end including the engine compartment lid form part of the passive pedestrian protection. 22 F80/F82 Complete Vehicle 3. Body 3.2.2. Side view F82 M4 Coupe, side view Exterior mirror and sill The exterior mirrors are heated (as standard equipment) and are electrochromic shaded with integrated side repeaters, have memory and fold-in functions and the passenger side mirror an automatic parking function. The mirror triangle and mirror cap at the bottom, including the weather strips, are also grained as standard equipment. The M3/M4 Coupe exterior mirrors have a prominent design and have been enhanced in terms of their aeroacoustic properties. The full panel covering of the side sill has also been enhanced in terms of aerodynamics. F80 M3 gill and mirror 23 TG14-I F80/F82 Complete Vehicle 3. Body Front fenders The front fenders of the F80/F82 are made from aluminum. There is an overall weight saving of 2.6 kg for the two fenders in comparison to the steel fenders of the F3x M3. Striking design feature include the M gills and the M3/M4 Coupe model inscription on the left/right front fenders. In addition, for the first time in a BMW M vehicle the Air Breathers are used on the left and right in the fenders, which were integrated in the typical M gill. The front fenders are also new due to the tire clearance. The fender flares were enlarged about 28 mm for the F80 compared to the F30 and about 18 mm from the F82 compared to the F32. Rear fender The rear fender is also new due to the tire clearance. Wheel arch cover The wheel arch cover and the covers of the steering units are adapted to the new fenders. 24 F80/F82 Complete Vehicle 3. Body Roof The roof operating unit for the F80/F82 is made from a carbon fiber structure and is connected to the body by bonding. The roof line has an aerodynamic outline in the middle section, thus highlighting the sporting character of the new M3/M4 Coupe. For the first time a CFRP roof is also used for a M3 Sedan. If the customer decides in favor of an electrical glass sunroof in the new M3/M4 Coupe, the CFRP roof is deleted and a steel roof, similar to the F3x M3, is installed. The production of the CFRP roof is done as a multi-layer design in the RMT process (transfer moulding) and is sealed with a layer of clear coat. In comparison to the standard steel roof, this CFRP roof saves about 5 kg in weight in the M3 and about 6.5 kg in the M4 Coupe. A CFRP convertible top bow is used as a supplement and support for the CFRP roof in the M4 Coupe. This CFRP convertible top bow sits in the middle at the height of the B-pillar and has a hybrid design. In comparison to the standard version, another 1.5 kg could be saved with the use of this CFRP convertible top bow. The CFRP roof structure thus also contributes to the consistent lightweight construction concept of the new M3/M4 Coupe. F80 M3 CFRP roof 25 F80/F82 Complete Vehicle 3. Body Rim design Forged 18" M BMW light-alloy wheels are used as standard at the front and rear. Mixed tires with the sizes 255/40 ZR18 at the front and 275/40 ZR18 at the rear are used. The forged M BMW light-alloy wheels with 19" and the mixed tires in the size 255/35 ZR19 at the front and 275/35 ZR19 at the rear can also be ordered as optional equipment in two different colors. For more information please see the chapter "Wheels/tires". F80/F82 rim design Index Explanation 1 18" M standard wheel 2 19" M wheel, optional equipment, two colors 26 F80/F82 Complete Vehicle 3. Body 3.2.3. Rear fender and rear view Rear fender The rear fender was widened and adapted to house the modified chassis and suspension components of the new M3/M4 Coupe. A striking design feature is the four round exhaust tailpipes. F80 M3 Rear view The rear bumper panel accommodates the exhaust system and its aerodynamics have been enhanced. The PDC sensors are painted in the vehicle colors. The shaped element in the bumper support is adapted to the shape of the M3/M4 Coupe bumper panel. 27 rGM F80/F82 Complete Vehicle 3. Body 3.2.4. Trunk lid Trunk lid F80 M3 The trunk lid of the F80 M3 is a standard part adopted from the F30. It is enhanced with a M-specific rear spoiler edge (Gurney). The rear diffuser and the Gurney increase the downforce at the rear axle, in particular at higher speeds. The Gurney is an aerodynamic component (named after the former Formula 1 driver) which functions as a tear-off edge. The Gurney enhances downforce at the rear axle and thus contributes to the optimization of the driving dynamics. F80 M3 Gurney Trunk lid of F82 M4 Coupe The trunk lid of the F82 M4 Coupe is a new design especially for the M4 Coupe, it was modelled after the BMW M3 CSL. It’s made from carbon and other fiber composites C-SMC, similar to previous vehicles (FI 2, FI 3, F06, E63 and E64). The shape of the trunk lid was enhanced for perfect aerodynamics so that no additional rear spoiler edge is necessary due to the integrated tear-off edge (Gurney). The exterior shell at the top and bottom is made from hollow glass spheres in the Low Density-Sheet Moulding Compound (LD-SMC) procedure. The mounting (including the threads) is made from sheet steel and cathodic dipped (E-coated) and then bonded to the interior shell. The interior shell is made from carbon fibers in the Carbon Fiber-Sheet Moulding Compound (C-SMC). The trunk lid of the M4 Coupe has its own M styling, adapted to the M4 Coupe rear fenders, and the contoured line of the CFRP roof is continued into the trunk lid. The trunk lid of the F82 is longer and higher in comparison to the F32, and is about 5 kg lighter. 28 F80/F82 Complete Vehicle 3. Body F82 M4 Coupe, trunk lid A_ Further information on the installation-disassembly and repair of the trunk lid can be found in ISTA (Integrated Service Technical Application). 3.2.5. Underbody and thermal protection Underbody The entire vehicle underbody is fully cladded and thus integrated into the aerodynamics concept of the M3/M4 Coupe, in order to reduce lift at the front and rear axle and distribute it evenly. This highlights and optimizes the driving dynamics concept, particularly at higher speeds. The underbody panels were adapted in terms of the cooling and flow around and through the drive components as well as chassis and suspension components, without compromising the aerodynamics concept. Thermal protection New heat insulation: • The heat insulation of the underbody panels is new. • The heat insulation of the fuel tank is new. • The heat insulation of the tunnel is new. • The heat insulation of the front and rear silencer is new. • A completely new heat insulation of the luggage compartment prevents it from heating up too much due to the hot exhaust air flow near the rear axle differential. 29 F80/F82 Complete Vehicle 3. Body 3.3. Interior 3.3.1. Driving area and steering wheel M driving area F80/F82 driving area For the full Merino leather upholstery (option X3) the instrument panel at the top and the door sills are covered with black Nappa leather and leather Merino in the upholstery color at the bottom of the instrument panel. 30 F80/F82 Complete Vehicle 3. Body M leather steering wheel The M leather steering wheel with multifunction is built on a magnesium armature and is based on the steering wheel used with FI 0 M5. Above the thumb rests are the M gearshift paddle with M shifting logic (left downshift, right upshift). In comparison to the F3x M3, the inner diameter of the steering wheel was reduced by 8 mm and the outer diameter by 2 mm. The steering wheel rim was reinforced to 31.6 mm in comparison to the standard version and enhanced in terms of ergonomics from a round to an oval cross-section which improves the grip. The color M stitching is another difference to the F3x M3. The M leather steering wheel in the double¬ spoke design with a stainless steel center trim and with M inscription is black leather. Steering wheel heating and the lane change warning are available as optional equipment. Two MDrive buttons are integrated in the left multifunction field. For more details please see the chapter "M Drive menu". F80/F82 M steering wheel 3.3.2. Leather trim Four colors of the leather interior equipment highlight the connection of the BMW M3/M4 Coupe to motor racing in different ways. In addition to deep black, Silverstone portrays the cool technical sporting character of the model, whereas Sakhir Orange highlights the dynamics and superior force of the model, and Sonoma Beige emphasizes classic modernity. 31 F80/F82 Complete Vehicle 3. Body 3.3.3. Seats M sport seats 10-way power front M sport seats with single-piece back panel, 4-way lumbar support, power- adjustable side bolsters and backlit M logo on backrest. Includes memory system for driver's seat and outside mirrors (2 positions). Anthracite Carbon Structure Cloth/Leather upholstery is standard equipment. The following equipment is available for the M sport seat in the US market: • Fully electric seat adjustment with memory function for the driver's side (standard). • Seat heating for driver and front passenger (standard). • Full Merino leather (optional). • Extended Merino leather (optional). M bucket seats 32 F80/F82 Complete Vehicle 3. Body Rear seat with lightweight through-load system The rear M seats also have a sport style, similar to the front seats. The rear row of seats is designed to split into a 60:40 combination. The rear row of seats is also distinguished by its design as a lightweight through-loading facility. With this design the backrest support structure is made in polypropylene injection moulding and reinforced with 30% glass fiber in sandwich technology. This design results in a weight saving of about 6 kg in comparison to the standard part. Possible optional equipment for the rear seat: • Seat heating for the F80/M3 • Merino leather and Merino full leather • Ski bag 3.3.4. Doors and decorative strips Doors The door trim panels have been adapted and are M-specific. In the basic version the exterior mirrors are in fabric, the armrests and handles are in Dakota leather. Other equipment details can be found in the sales documentation. M3/M4 Coupe, interior design • "Blue Shadow" decorative strips as standard and "Aluminum Blade" decorative strip as optional equipment. These interior trim finishers are currently only offered for the F80/F82. • Carbon decorative strips specific to M as known from the FI 2/FI 3 M. • Fine wood trim Fine-line Anthracite adopted from the production vehicles of BMW AG. The interior trim finishers are located in the instrument panel. • The door sill cover strips have a M3/M4 Coupe inscription. • M footrest with a stainless steel design and M emblem. • The function panel M DCT Drivelogic is in fine-brushed aluminum with Drivelogic button. 33 F80/F82 Complete Vehicle 4. Powertrain 4.1. Engine S55B30T0 The S55B30T0 engine is described in its own manual, the ST1404 S55 Motorsport Engine reference manual (available in ICP and TIS). F80/F82 S55B30T0 Engine 4.2. Transmission 4.2.1. Manual gearbox In the F80/F82 a manual gearbox is installed as standard equipment. It is an enhanced version of the familiar K-transmission, which is known from the production vehicles of BMW AG. The transmission was adapted to the higher power requirements of the M3/M4 Coupe. 34 rGT4-C F80/F82 Complete Vehicle 4. Powertrain The following components were modified: • Weight reduction of about 12 kg in comparison to the previous transmission in the E9x M3. • Smaller in size which contributes to the lower weight. • Improved shifting comfort due to use of new type of carbon friction lining in the synchronization units. • Increased efficiency with dry sump lubrication ("splash" lubrication and targeted oil ducts are no longer used). This results in a reduction of heat development to the extent that external cooling (like in the E9x M3) is not necessary. • Reduction of noise level. Engine speed adaptation for a gear change (double clutch) The new F80/F82 engine uses speed adaptation for the manual gearbox (Similar to the production vehicles with the B-engines with manual gearboxes). The engine speed adaptation further highlights the sporting character of the new F80/F82 and its motor racing genes. In addition, the engine speed adaptation is used to reduce the drag torque and improve the driving stability in the dynamic handling characteristics at the limit range. The engine speed during a gear change is automatically adapted to the new transmission ratio. The engine and the transmission input shaft thus have the same speed when engaging the clutch. This ensures the clutch is always engaged smoothly. The corresponding engine speed is calculated by the DME and held for a maximum of two seconds. With M Driving Modes the engine speed is adapted at different rates depending on the driving mode. For the control the clutch pedal must be pressed fully when switching. The engine speed adaptation for the gear change is not active. The engine speed adaptation for a gear change can be deactivated via the diagnosis system. The engine speed adaptation includes the following components and functions: • New gear sensor via x-y axle, detects gearshift request and communicates directly with the engine control unit. • Clutch switch is two-stage and communicates directly with the DME. • Engine speed adaptation characteristic is based on the selected driving mode. • No reverse gear switch as detection via gear sensor. The function of the engine speed adaptation in the F80/F82 differs to the FI 0 M5 in the following point: • No engine speed recording via the synchronization unit. • The detection of the transmission input speed was done at a gear (constant gear) in the transmission. The determination of the transmission ratio had to be calculated from the wheel speed (counted back to transmission output speed) and transmission input speed. 35 F80/F82 Complete Vehicle 4. Powertrain A_ __ In the DSC "OFF" mode the engine speed adaptation is switched off in order to give the driver full control over the vehicle. A_ The neutral sensor is capable of self-diagnosis and if necessary can input a fault in the fault memory. An additional display is not done. After the replacement of the gear sensor it must be re-calibrated with help of the BMW diagnosis system. 4.2.2. Clutch A double-disc clutch is installed in combination with the manual gearbox. The operating principle of the clutch is identical to the double-disc clutch systems already used. 4.2.3. M double-clutch transmission (M DCT) with Drivelogic The GS7D36BG M DCT with Drivelogic is available as optional equipment. The DCT in the new F80/F82 has the same technical features as the DCT in the FI 0 M5, FI 2 M6, F13M6, and F06 M6. The M Double-clutch Transmission with Drivelogic was used (for the first time) in the E93 M3 with the S65B40 engine with the designation GS7D36SG. This transmission is described in the M DCT web course and in the ST813 M DCT transmission training manual available in ICP and TIS. F80/F82 external view, M DCT Drivelogic 36 F80/F82 Complete Vehicle 4. Powertrain The following changes have been introduced to adapt the DKG to the F80/F82: • Adapted transmission housing for the S55 engine • Removal of the emergency gearbox release (parking lock) • New thermostat with modified temperature map • New mechatronics module to satisfy future software requirements • New M DCT power steering cooler supplier F80/F82 M DCT Drivelogic with external oil circuit Index Explanation 1 Transmission oil cooler 2 Thermostat 3 M Double-clutch Transmission Drivelogic 4 M gear selector switch 37 F80/F82 Complete Vehicle 4. Powertrain 4.2.4. Structure and power flow Design The transmission housing and the shaft bearing were adopted in their existing form from the GS7D36BG. However the connection to the engine (bell housing) was adapted for the S55. Index Explanation 1 Central input shaft with clutch input 2 Clutch 1 3 Clutch 2 4 Inner input shaft 2 5 Inner input shaft 1 6 Auxiliary shaft 7 Constant gears 8 Output shaft 9 Selector sleeves 10 Parking lock 38 F80/F82 Complete Vehicle 4. Powertrain Power flow, gears Schematic diagrams of the power flow of all gears: 39 F80/F82 Complete Vehicle 4. Powertrain 40 F80/F82 Complete Vehicle 4. Powertrain The fifth gear was stepped up for the E9x M3 and is now the direct gear in the Fix M5/M6 and F8x M3/M4 Coupe. 41 F80/F82 Complete Vehicle 4. Powertrain The sixth gear was stepped up for the E9x M3 and is now reduced in the Fix M5/M6 and F8x M3/M4 Coupe. F80/F82 M DCT, reduced 6th gear The seventh gear was the direct gear in the E9x M3 and is now reduced in the Fix M5/M6 and F8x M3/M4 Coupe. 42 F80/F82 Complete Vehicle 4. Powertrain 4.2.5. Technical data of M DCT GS7D36BG in the F80/F82 and Fix M vehicles in comparison to GS7D36SG in the E9x M3 Vehicle E9x M3 Fix M vehicles F80/F82- M3/M4 Coupe Gear ratio spread* 4.8 7.2 7.2 Maximum engine speed [rpm] 9000 7500 7600 Selection torque [Nm] 520 700 700 Dry weight without dual¬ mass flywheel [kg] 85 85 83.2 Ratio [:1] Ratio [:1] Ratio [:1] Constant 1,630 1,630 1,630 Switch position 1st gear 4,780 4,806 4,806 2nd gear 3,056 2,593 2,593 3rd gear 2,153 1,701 1,701 4th gear 1,678 1,277 1,277 5th gear 1,390 1.000 1.000 6th gear 1,203 0,844 0,844 7th gear 1.000 0,671 0,671 Reverse gear 4,454 4,172 4,172 Rear axle 3.154 3.154 3.462 * The Gear ratio spread is calculated by dividing the gear ratio of the first gear by the highest forward gear. 43 F80/F82 Complete Vehicle 4. Powertrain 4.2.6. System information System wiring diagram F80/F82 M DCT, system wiring diagram 44 TE14-C110 F80/F82 Complete Vehicle 4. Powertrain Index Explanation 1 Dynamic Stability Control (DSC) 2 Digital Motor Electronics (DME) 3 M Double-clutch Transmission (M DCT) with Drivelogic 4 Power distribution box, front 5 Front Electronic Module (FEM) 6 Integrated Chassis Management (ICM) 7 Drivelogic button 8 M gear selector switch (M GWS) 9 Brake light switch 10 Steering column switch cluster (SZL) 11 M steering wheel shift paddle 12 Accelerator pedal module 13 Instrument panel (KOMBI) 45 F80/F82 Complete Vehicle 4. Powertrain Inner sensor system The sensor system was able to be adopted unchanged from the GS7D36BG of the Fix M5/M6 vehicles. )$ >i s a 4 - 2 < F80/F82 M DOT, schematic diagram of inner sensor system Index Explanation 1 Input speed hall effect sensor 2 Transmission input speed hall effect sensor of the inner input shaft 2 3 Transmission input speed hall effect sensor with detection of direction of rotation of inner input shaft 1 4 Clutch oil pressure Piezo sensors 5 Temperature NTC sensors 6 Shift travel hall effect sensors 7 Parking lock hall effect sensor (redundant) 46 F80/F82 Complete Vehicle 4. Powertrain 4.2.7. M gear selector switch The functional structure and the operation of the M gear selector switch are identical to those in Fix M and F06 M6 vehicles with M DCT Drivelogic. F80/F82 M DCT Drivelogic gear selector switch and driving dynamics button Index Explanation 1 DSC button (with M dynamic mode) 2 Engine dynamics button 3 M gear selector switch 4 M DCT Drivelogic button 5 Servotronic button 6 M sports suspension button (EDC) 4.2.8. Drivelogic The number of driving programs is the same as that in Fix M and F06 M6 vehicles. However the design of the Drivelogic button has changed. Instead of a rocker type button (as the E9x M3 and for Fix M vehicles), the F80/F82 uses a normal pressure switch for clicking through the programs. After each change between sequential mode and Drive mode the last selected driving program is active. After each engine start driving program 1 is active in Drive mode. Drive mode Three driving programs are available: 1: Efficient drive 2: Relaxed drive 3: Sporty drive 47 F80/F82 Complete Vehicle 4. Powertrain Sequential mode Three driving programs are also available here: 1: Comfortable gear shifts. 2: Sporty, fast gear shifts. 3: Maximum shift speed and the requirement for the activation of the launch control. To use the highest, i.e. the third driving program, the DSC does not have to be activated. 4.2.9. Launch Control Launch Control enables optimal acceleration when driving off on a smooth roadway. A During the first 5,000 km (3,100 miles) the launch control should generally not be used (see also the chapter on driving tips in the Owner's Manual). The 2,000 km (1,242 miles) pre-delivery check must have been completed and reset/confirmed with the Integrated Service Technical Application (ISTA) (do not reset via the instrument cluster service function, as otherwise the launch control is not enabled). Premature wear occurs as a result of the high load of the vehicle with use of the launch control. Launch mode preconditions Sequence Precondition/Action 1 The vehicle must be stationary, the engine running and at operating temperature (about 10 km (6 mile) warm-up journey). 2 The DSC is deactivated. 3 The sequential mode and the third Drivelogic driving program are selected. 4 The brake pedal is gently pressed with the left foot. 5 The accelerator pedal is pressed fully and held in this position. 6 In the M instrument cluster a flag symbol must appear (if not, check notes and steps 1-5). 7 An engine speed for pulling away of about 3500 rpm is set, which can be modified up or down in the cruise control settings by a maximum 500 rpm in 100 rpm increments. 8 The left foot is taken off the brake within 3 seconds. 48 F80/F82 Complete Vehicle 4. Powertrain Effect The Launch Control shifts up to 5th gear independently with the shortest possible shifting times and enhanced driving performance shift points as long as the driver has the accelerator pedal pressed in fully and a time limit of 22 seconds is not exceeded for the acceleration. The start flag in the instrument cluster remains active. Automatic deactivation • The driver releases (also if only temporary) the accelerator pedal full load position during acceleration or the acceleration phase reaches a duration of 22 seconds. If even one of these preconditions is not met, it is not possible to activate the Launch Control. Also at excessive transmission oil temperature (e.g. repeat Launch Control or race-like start), activation is not allowed and locked until an acceptable temperature threshold is reached. The start flag goes out with every deactivation and the automatic forced upshift is cancelled. 4.2.10. Transmission control unit The M DCT control unit is installed in the mechatronics module in the transmission similar to the GS7D36SG. The software is adapted to the F80/F82. 4.2.11. Emergency gearbox release A_ The emergency gearbox release is deleted similar to the F10, FI 2, FI 3 and F06. For towing away please observed the information in the Owner's Manual of the vehicle. 49 F80/F82 Complete Vehicle 4. Powertrain 4.2.12. Service information Transmission oil circuit When work is required on the oil circuit of the DCT (regardless if it is the M DCT or AG DCT), for example after an accident, or if the oil circuit has to be opened due to a repair, there must be maximum cleanliness. This includes: • Thoroughly cleaning the outer oil circuit areas before disassembly of the components or opening the oil circuit. • All openings and lines must be closed immediately after disassembly with clean original plugs. Do not use unsealed components or replacement parts of the oil circuit without checking for cleanliness. • The workbay at which a M DCT is opened must be extremely clean and secured against dirt contamination, also during work interruptions. For example by covering with a clean and lint- free cover. Lifetime oil filling Similar to the E9x M3 and Fix M5/M6 with M DCT Drivelogic, no transmission oil change is currently planned at 2,000 km/1200 miles (pre-delivery check) or every third engine oil change. Repair/Part exchange Depending on the type of repair, the data status of the M DCT must be read out beforehand and read in again after the component has been replaced (e.g. replacement of mechatronics module). Depending on the type of repair (e.g. dual clutch change), the "Neutral" gear selection position must be selected before the engine is stopped. A_ The current information and specifications in the documents in the Integrated Service Technical Application (ISTA) must be observed in each case. 50 F80/F82 Complete Vehicle 4. Powertrain 4.3. Driveshaft For the first time a one-piece carbon driveshaft is used in a BMW M vehicle. Traditionally steel or aluminum driveshafts are required for a vehicle designed for high performance. In order to be able to transmit the torque and engine speeds they are designed as a two-piece component and have a center mount. Only this design ensures high-speed performance, "critical bending speed". The tube element of the new M3/M4 Coupe carbon driveshaft enables a one-piece design due to its specific material properties. High rigidity was achieved with the tubular design of the driveshaft and the low density of the carbon material used in its fabrication. In addition, the legally mandated safety requirements were able to be integrated in the design. The significant weight saving along with excellent rigidity was able to be realized by using low material density of carbon and eliminating the center mount. In addition other desired requirements, such as corrosion resistance, low length compensation and enhanced comfort (oscillation acoustics) can be satisfied with the use of the carbon driveshaft. In comparison to the predecessor driveshaft in the E9x M3, the weight was able to be reduced by 5.3 kg to 7.6 kg. F80/F82 carbon driveshaft Index Explanation 1 Flexible disc joint 2 Pipe adapter, front 3 Support ring 4 Carbon pipe 5 Pipe adapter, rear 6 Sliding piece 7 Flange, rear axle differential 51 F80/F82 Complete Vehicle 4. Powertrain 4.3.1. Service information • During disassembly ensure that the carbon driveshaft is removed first at the rear (at the sliding piece) and then at the front carrier (flexible disc). The installation should be done in the reverse sequence. • In the sliding piece there is a grease filling, which is coordinated precisely to requirements and is required for the function. Therefore, do not remove the grease cap before the driveshaft is pushed together for the installation at the sliding piece. Remove the grease cap after the pushing together and then screw the driveshaft at the rear axle differential. • Please check the U-type bellows again after pushing together. The U-type bellows should not arch outwards, bend back if necessary. A_ The carbon driveshaft is highly sensitive to impacts, therefore the driveshaft should not be stored in an upright position. The carbon driveshaft should be stored in a horizontal position or suspended. Also during this storage period keep the carbon driveshaft away from impacts. A clear indicator protective layer (woven fabric) is attached to the carbon driveshaft. If the carbon driveshaft was subjected to an impact, small cracks in the form of a spider web appear on this layer. Damage can be identified by means of this crack and the necessary measures deduced from a damage pattern catalog in the Integrated Service Technical Application (ISTA). The current information and specifications in the documents found in the Integrated Service Technical Application (ISTA) must be observed in each case. F80/F82 carbon driveshaft, indicator layer 4.4. Rear axle final drive 4.4.1. Active M Differential This electronically/electromechanically controlled rear axle differential lock was developed especially for the F10 M5, it is used in the F06/F12/F13 M6 and now in the F80/F82. 52 F80/F82 Complete Vehicle 4. Powertrain The M rear axle differential, size HAG 220 (ring gear 0 220 mm), is used with a M rear axle differential lock. The system designation for this is "regulated rear axle differential lock", the control unit designation is GHAS (Geregelte Hinter Achsgetriebe Sperre (regulated rear axle differential lock). This variable M differential lock II replaces the variable M differential lock I in the M rear axle differential HAG 215 (ring gear 0 215 mm) used in the E9x M3. The gear ratio of the HAG 220 is 3,154:1 (HAG 215: 3,615:1). This M rear axle differential can be recognized by an aluminum oil sump assembled from below and an electric motor which is visible from the outside. The HAG 220 is about 2.8 kg heavier than the HAG 215 at 49.7 kg. F80/F82 GFIAG, external view Demand-controlled lock The lock is a demand-controlled rear-axle differential lock which is active in the following situations: • Pulling away. • Differential speed at the rear axle for straight-ahead driving under tension due to various coefficients of friction, left/right. • Dynamic cornering tensioned. • Power oversteer (drifting). • Stabilization in coasting/overrun mode. Traction, handling and driving stability are enhanced by adjusting a defined differential speed or differential torque at the rear axle. The regulated M rear-axle differential lock works with a position-controlled electric motor and a ball ramp. The GHAS control unit is installed above the Rear Electronic Module (REM), at the rear right inner fender. 53 F80/F82 Complete Vehicle 4. Powertrain 4.4.2. Structure/Function The lock-up torque is generated by a multi-disc clutch. The necessary axial pressure is applied to the multi-disc clutch by the position-controlled direct current motor by means of gears and a ball ramp mechanism. The clutch package operates between the differential housing (steel outer discs) and the right output (molybdenum-coated steel inner discs). F80/F82 rear axle differential, section view System components: • Wiring harness • Regulated differential lock control unit (GHAS) • Electric motor and transmission gearing • Lock 54 TA11-10C F80/F82 Complete Vehicle 4. Powertrain F80/F82 components of the locking differential: Exploded diagram Index Explanation 1 Electric motor 2 Intermediate gear 3 Ball ramp consisting of geared mobile adjusting disc and first half of ball ramp 4 Balls/Spherical washers 5 Fixed pressure disc with second half of ball ramp 6 Axial needle bearing 55 TA11-1021 F80/F82 Complete Vehicle 4. Powertrain Index Explanation 7 Axial bearing thrust washer 8 Circlip (ball bearing fixing) 9 Ball bearing between inner output hub and differential housing 10 Disc spring pressure ring 11 Diaphragm spring 12 Differential lid (connected to differential housing, cannot rotate) 13 Pressure plate 14 Disc set 15 Counter pressure plate Index Explanation 1 Electric motor 2 Intermediate gear 3 Ball ramp consisting of geared mobile adjusting disc and first half of ball ramp 4 Balls/Spherical washers 5 Fixed pressure disc with second half of ball ramp 56 F80/F82 Complete Vehicle 4. Powertrain Index Explanation 6 Axial needle bearing 7 Axial bearing thrust washer 8 Circlip (ball bearing fixing) 9 Ball bearing between inner output hub and differential housing 10 Disc spring pressure ring 11 Diaphragm spring 12 Differential lid (connected to differential housing, cannot rotate) 13 Pressure plate 14 Disc set 15 Counter pressure plate 16 First output bevel gear 17 Second output bevel gear 18 Differential housing (connected to outer discs) The electric motor (1) is bolted on to the housing and the pressure disc fixed to the second ball ramp half (5) in the housing. The mobile components of the ball ramp (2, 3 and 4) generate the necessary axial displacement of the pressure disc (5). These components are not subject to the differential transmission rotation and are disconnected from the rotating components by an axial needle bearing ( 6 ). The components with the index 6 to 18 belong to the differential and rotate proportional to the rear axle gear speeds. The locking is done between the right output (16) and the differential housing (18) and counteracts a difference in speed between the output bevel gears (16 and 17). The disc spring (11) opens the lock when the engine is not supplied with current. 4.4.3. System information The GHAS control unit evaluates the dynamic handling characteristics parameters made available by other control units via the FlexRay data bus and determines the lock-up torque to be applied. The DSC control unit can also request separate and higher-level locking interventions to stabilize the vehicle both when the DSC is activated and deactivated. The position-controlled direct current motor is activated directly by the power electronics of the GHAS control unit with vehicle voltage via a pulse-width-modulated signal. The frequency is 12.8 kHz and the maximum current level is 30 A. The electric motor is equipped with two hall effect sensors to determine its position and the direction of rotation. 57 F80/F82 Complete Vehicle 4. Powertrain System wiring diagram $ •CM ® F80/F82 GFIAS, system wiring diagram 58 TE14-0163 F80/F82 Complete Vehicle 4. Powertrain Index Explanation 1 Dynamic Stability Control (DSC) 2 Digital Motor Electronics (DME) 3 Front Electronic Module (FEM) 4 Integrated Chassis Management (ICM) 5 Components of the regulated rear axle differential lock 6 Control unit of the regulated rear axle differential lock (GHAS) 7 Power distribution box, rear Interfaces The regulated differential lock (GHS) control unit works with the following control units and includes the following information: Control unit Bus system Information FEM - Terminal status - Vehicle identification number (for encoding) - Vehicle condition (power management and fault memory block, e.g. in the event of voltage drop by engine start) DME PT-CAN/FlexRay - Accelerator pedal angle - Wheel drive torque - "Engine running" signal DSC FlexRay - Wheel speed - Setpoint axial torque distribution - Stabilization status - Brake value ICM FlexRay - Tolerance adjustment of wheel (adjustment of different wheel circumferences) - Lateral acceleration - Yaw rate - Driving speed - Road longitudinal tilt - Steering angle FEM-ZGM Gateway for all bus systems Forwarding of information to regulated differential lock Electric motor location determination To determine the position of the electric motor two hall effect sensors in the motor are evaluated. To determine the characteristic curve of the lock-up torque via the motor position a re-calibration is regularly performed to compensate for the wear in the clutch. 59 F80/F82 Complete Vehicle 4. Powertrain In order to be able to assign a corresponding clutch lock-up torque to a certain position of the servomotor, and to take wear influences into consideration, every 1000 km (621 miles) or after an energy input in the lock of 100 kJ (corresponds to a lap of the Nurburgring) a reference run is performed after the engine is shut down. During this reference run the motor is subjected to a defined current level. The lock-up torque 1500 Nm (1106 Ib-ft) is assigned to the resulting position. Temperature monitoring Three temperature sensors are installed. The temperature of the control unit (driver output stage), the temperature of the electric motor and the transmission oil temperature are monitored. The temperature thresholds are as follows: Control unit 105 °C (221 °F) Electric motor 160 °C (320 °F) Oil temperature 190 °C (374 °F) The current oil specification is "BMW final drive oil synthetic MSP/A" (for e.g. Castrol SAF-XJ) and is the same oil used in the previous M vehicles with variable M differential lock. The capacity is currently 1.21(1.27 qrt). The current specification in our service information "Operating materials" and the technical data in the Integrated Service Technical Application (ISTA) must be observed in each case. A If, due to a fault, the GHAS lock function is switched off or fails, a locked differential is automatically reopened as the lock function is not self-locking. The driver is warned and informed regarding the effects that can be expected: 1. Loss of traction with dynamic driving style and low coefficients of friction, particularly with different coefficients of friction, left/right. 2. Possible deterioration of stability in dynamic driving situations. 4.4.4. Service information • For a replacement of the GHAS control unit an encoding (activation of vehicle-related characteristic curve) and then an initial calibration are necessary and then the fault memory must be deleted. • After the replacement of the entire M rear axle differential a calibration must be performed and then the fault memory must be deleted. • For a replacement of the electric motor, electric motor plus intermediate gear or oil temperature sensor, only the fault memory must be deleted. The final drive oil is currently replaced every 2000 km/1200 miles (pre-delivery check) and at every third engine oil change. A The current information and specifications in the Integrated Service Technical Application (ISTA) must be observed. 60 F80/F82 Complete Vehicle 4. Powertrain 4.4.5. Half-shafts As is typical for BMW M vehicles, the output shafts have a hollow design in order to make optimal use of the material in relation to material usage, weight and rigidity. These lightweight half-shafts are designed to transmit up to 7000 Nm (5163 Ib-ft) torque. The CV joints and the trunnion mounts of the F80/F82 are drilled hollow. This is the first time this intelligent lightweight construction was implemented in a M vehicle. F80/F82 output shaft Index Explanation 1 CV Joint drilled hollow on the wheel-side with trunnion mount 2 Boot 3 Hollow shaft 4 CV Joint drilled hollow at the rear axle differential with trunnion mount The special feature of the output shafts is the double-sided gearing. They are no longer flange- mounted at the rear axle differential and inserted in the wheel hub, but are inserted in the rear axle differential and in the drive flange. The procedure has thus changed for installation and removal. A The current information and specifications in the Integrated Service Technical Application must be observed. 4.4.6. Wheel flange The intelligent lightweight construction was also implemented with regard to the wheel flanges of F80/ F82. 61 F80/F82 Complete Vehicle 4. Powertrain The wheel flange at the front axle and the rear axle have been enhanced in relation to their weight. The material has been reduced at places subject to little stress, and accumulated at heavily stressed places. With these measures provide a weight saving of about 1.13 kg (2.5 lbs) in comparison to the E9x M3. F80/F82 wheel flange Index Explanation A Wheel bearing unit with front wheel flange B Drive flange, rear 62 F80/F82 Complete Vehicle 5. Chassis and Suspension F80/F82 chassis and suspension, complete The chassis and suspension is based on the technology of the F3x and the E9x M3, whereby almost all components are again new and specific to M or have been adapted. Designation Unit E9x M3 F10M5 F80/F82- M3/M4 Coupe Wheelbase/turning circle [mm/m] 2761/11,7 2964/12,4 2812/12,2 Front track width [mm] 1540 1627 1579 Rear track width [mm] 1539 1582 1603 Front Axle M two-joint spring-strut front axle M double¬ wishbone axle M two-joint spring-strut front axle Steering Hydraulic M rack-and-pinion steering with M Servotronic Hydraulic M rack-and-pinion steering with M Servotronic Electrical rack-and- pinion steering (EPS) with M Servotronic Average overall ratio 12.5 13,05 15 Steering wheel turns End stop-end stop 2,4 2,6 2,5 Rear axle M 5-joint rear axle M Integral IV (based on E60 M5) M 5-joint rear axle Axle ratio 3.154 3.154 3.462 63 F80/F82 Complete Vehicle 5. Chassis and Suspension 5.1. Front Axle The front axle is based on the M two-joint spring strut front axle of the E9x M3. All components or the bearings are new to M or have been adapted and the M front axle support has been reinforced with a stiffening plate, typical of M. ® ® ® ® F80/F82 two-joint spring strut front axle Index Explanation 1 M front axle support 2 M anti-roll bar link 3 M spring strut with support bearing 4 M swivel bearing 5 M wheel bearing unit with wheel flange 6 M track rod 64 TF14-0167 F80/F82 Complete Vehicle 5. Chassis and Suspension Index Explanation 7 M wishbone 8 M trailing link with hydro mount 9 M anti-roll bar 10 M Servotronic (EPS) 11 M stiffening plate All components have been redesigned for the increased requirements. The guiding of the wheel for compression and steering is done via the wishbone, the tension strut, the spring strut and the track rod. In order to guarantee precise wheel guiding in transverse direction of vehicle, the power is transmitted from the swivel bearing to the front axle guide via the ball joints with no play. In order to also guarantee this in a longitudinal direction, the chassis and suspension forces are transmitted via specially developed elastomer bearings for the F80/F82 via the tension struts to the front axle support. The stiffening plate and the additional screw connections of the axle support and the side sills also ensure an increase in the transverse rigidity of the front of the vehicle by about 30%. The connection between the spring strut and the swivel bearing was realized by a clamp connection similar to the E82 M and E9x M3. 65 F80/F82 Complete Vehicle 5. Chassis and Suspension F80/F82 spring strut-swivel bearing connection Index Explanation 1 M spring 2 M spring strut 3 M anti-roll bar link 4 M swivel bearing 5 M wheel bearing unit with wheel flange 6 M wishbone 7 M tension strut 8 M anti-roll bar 9 M front axle support The intelligent lightweight construction of the F80/F82 also was implemented in the front axle concept. The wishbone, wheel carrier, axle support and the stiffening plate are manufactured in lightweight aluminum. 66 F80/F82 Complete Vehicle 5. Chassis and Suspension A weight saving of about 5 kg was achieved with these measures in comparison to the F3x M3. Further weight savings were achieved with the design of the spring strut in aluminum, as well as the tubular design of the anti-roll bar (as in the E9x M3). The design of the front axle was done in close cooperation with the tires which were also specially developed for the F80/F82. 5.1.1. Steering EfficientDynamics measures where also implemented on the new F80/F82. The rack-and-pinion steering has electrical steering wheel support "M Servotronic based on EPS". For power steering assistance is done via an electric motor located parallel to the steering rack housing. The power transmission is done via a ball screw design. The use of a M Servotronic (EPS) in the new M3/M4 Coupe results in a weight saving of about 3.5 kg in comparison to the hydraulic steering system in the E9x M3. F80/F82 steering 67 F80/F82 Complete Vehicle 5. Chassis and Suspension Index Explanation 1 M steering wheel 2 Adjustable steering column 3 Steering column 4 M track rod, left 5 M Servotronic (EPS) 6 M track rod, right The M Servotronic (EPS) is an independent development for the M3/M4 Coupe. All components of the M Servotronic (EPS) have been developed specifically for the M3/M4 Coupe. The development of the steering was able to be coordinated to the typical M properties. Special attention was paid to the typical M features: Direct steering sensation Driving condition feedback Dynamic driving at the vehicle’s stability limit Index Explanation 1 Reduction gear 2 Steering-torque sensor 3 Track rod 4 Control unit, M Servotronic (EPS) 5 Electric motor with rotor position sensor The ratio of the M Servotronic (EPS) was also adapted to the M3/M4 Coupe. It should be highlighted that after an eighth of a revolution of the steering wheel the rack ratio increases by 8% (similar to the production vehicle F3x with the optional equipment SA 2VL Variable Sport Steering). 68 F80/F82 Complete Vehicle 5. Chassis and Suspension Index Explanation 1 Rack in basic version of F3x (constant gear geometry) 2 Variable sport steering rack (variable gear geometry) A More indirect steering gear ratio (variable sport steering) B More direct steering gear ratio (variable sport steering) X Steering angle y Rack stroke With the use of the M Servotronic (EPS) in the new M3/M4 Coupe the parking assistance system "Parking Maneuvering Assistant" (SA 5DP) is now also offered. 5.1.2. Servotronic The Servotronic function known from traditional hydraulic steering systems is also used in the M Servotronic (EPS) and is installed in the M3/M4 Coupe as standard. It is a M Servotronic, which functions according to the same operating principle as in production vehicles. The difference in the M Servotronic is that three stages can be selected in comparison to two stages in the production vehicles, and it has a separate button in the driving dynamics button panel in the center console. The button or the configuration in the MDrive menu is used to switch between "Comfort", "Sport" and "Sport+". Here the corresponding characteristic curve is activated and in Sport direction the power steering support is also noticeably withdrawn. The program selection can also be pre-configured in the MDrive menu and selected via the M button on the steering wheel assigned to the MDrive. 69 F80/F82 Complete Vehicle 5. Chassis and Suspension 5.1.3. Steering angle sensor The information on the steering angle is not recorded by the Electronic Power Steering (EPS) and not via a separate sensor on the steering wheel, instead its calculated based on the motor position angle of the EPS motor in relation to the steering wheel. The EPS transmits the position of the rack to the ICM control unit via FlexRay. During this process, the EPS calculates the absolute position of the rack based on the current motor position of the EPS motor and the number of complete revolutions performed by the motor starting from the zero position (straight-ahead driving position). Taking this position as the starting point, the ICM control unit determines the wheel-specific steering angle among other things using the stored ratio parameters (rack to wheel-specific steering angle) and transmits this via FlexRay. This wheel-specific steering angle is used by the DSC among other things as a reference variable for internal control functions. In cases where the absolute value is not available from the EPS (loss of Terminal 30, flash process), the absolute value is determined through interaction between the ICM and EPS using an adaptation function in which the steering wheel is turned from end stop to end stop (e.g. straight-ahead position - > left -> right -> straight-ahead position). 70 F80/F82 Complete Vehicle 5. Chassis and Suspension 5.1.4. System wiring diagram, M Servotronic (EPS) 0 0 F80/F82 system wiring diagram, EPS F80/F82 Complete Vehicle 5. Chassis and Suspension Index Explanation 1 Dynamic Stability Control (DSC) 2 Digital Motor Electronics (DME) 3 M Servotronic (EPS) 4 Power distribution box, front 5 Power distribution box, engine compartment 6 Front Electronic Module (FEM) 7 Integrated Chassis Management (ICM) 8 Steering column switch cluster (SZL) 9 Instrument panel (KOMBI) Terminal 15N Ignition (after-run) Terminal 30 Terminal 30 5.2. Rear axle The M rear axle is based on the five-link rear axle from E9x M3. All components and bearings were redesigned for the increased requirements. © ® F80/F82 five-link rear axle © Y Index Explanation 1 M wheel bearing unit with drive flange 2 M control arm 3 M trailing arm 4 M wishbone 72 F80/F82 Complete Vehicle 5. Chassis and Suspension Index Explanation 5 M rear axle support 6 M camber control arm 7 M track control arm 8 M hub carrier All trailing arms and also the wheel carrier are manufactured in aluminum forging technology. This design reduces the unsprung masses of the wheel-controlling components in comparison to the E9x M3 by about 3 kg (6.6 lbs). F80/F82 five-link arrangement with wheel carrier Index Explanation 1 M wheel bearing unit with drive flange 2 M hub carrier 3 M control arm 4 M track control arm 5 M wishbone 6 M rear axle support 7 M camber control arm 8 M trailing arm The rear axle support itself is made from steel tubing which is similar to a steel tube grid frame. 73 F80/F82 Complete Vehicle 5. Chassis and Suspension This design is characterized by maximum rigidity and minimal weight. The M rear axle support is fixed to the body without a bearing. This fixed connection (bolted) directly to the body ensures an optimized wheel guiding and thus enhanced directional stability. In addition, through the use of diagonal struts a direct transmission of the longitudinal forces applied during braking to the body structure was achieved. F80/F82 rear axle support Index Explanation 1 Attachment point, rear axle at body (fixed (bolted) connection without rubber mount) 2 Attachment point for rear axle differential (GFIAG) 3 M rear axle support Further weight savings compared to the F3x M3 was achieved with the design of the spring strut in aluminum, as well as the tubular design of the anti-roll bar like in the E9x M3. The design of the rear axle was done in close cooperation with the tires which were also specially developed for the F80/F82. 74 F80/F82 Complete Vehicle 5. Chassis and Suspension 5.3. Brakes and wheels/tires 5.3.1. Brakes M Compound brake (?) (2) (3) F80/F82 brake system Index Explanation 1 Dynamic Stability Control (DSC) 2 Brake fluid expansion tank 3 Brake servo (left-hand drive vehicle) 4 Parking brake lever 5 Rear brake disc 6 Rear double-piston fixed caliper 7 Brake pedal 8 Clutch pedal 9 Front four-piston fixed caliper 75 F80/F82 Complete Vehicle 5. Chassis and Suspension Designation Unit E9x M3 F10M5 F80/F82-M3/ M4 Coupe Front brake 1 piston, floating caliper 6 pistons, fixed caliper 4 pistons, fixed caliper Brake disc, front [mm] 360 x 30 400 x 36 380 x 30 Rear brakes 1 piston, floating caliper 1 piston, floating caliper 2 pistons, fixed caliper Brake disc, rear [mm] 350 x 24 396 x 24 370x24 Parking brake mechanical electro¬ mechanical mechanical The front brakes are specific to the F80/F82. Large perforated M compound brake discs combined with a four-piston fixed calipers are used. The diameter of the brake disc is 20 mm larger than that of the E9x M3. All brake calipers will be blue with a color M logo irrespective of the external vehicle color chosen. F80/F82 front brake The rear brakes are specific to F80/F82. The diameter of the rear perforated M compound brake discs is 20 mm larger than that of the E9x M3. The rear brake calipers are double-piston fixed type. 76 F80/F82 Complete Vehicle 5. Chassis and Suspension M Carbon ceramic brake The M Carbon ceramic brakes are available as optional equipment from the series launch of the new F80/F82. In addition to the F10 M5, the FI 2 M6, FI 3 M6 and the F06 M6. The M Carbon ceramic brake system is also called C/SiC brake system. Depending on the situation, this offers a further increase in active safety compared to the M Compound brakes. In a direct comparison it also offers the following: • Even more direct/spontaneous use of brake force • Maximum heat resistance even with continuous sporty operation • Higher fading stability • Significantly reduced wear • 7 kg (15.4 lbs) weight reduction of rotating wheel masses • Increased suitability for winter driving conditions thanks to corrosion resistance. F80/F82 M Carbon ceramic brake, front axle As a visible distinguishing feature to the M Carbon ceramic brake system uses gold painted brake calipers with a color M logo. The F80/F82 Carbon ceramic brake system can only be used with the 19" M wheel rim due to the larger brake discs at the front. The brake discs are manufactured by Brembo SGL Carbon Ceramic Brakes GmbH. 77 F80/F82 Complete Vehicle 5. Chassis and Suspension Designation Unit F10 M5 F80/F82-M3/ M4 Coupe Front brake 6 pistons, fixed caliper 6 pistons, fixed caliper Brake disc, front [mm] 410x38 400x38 Rear brakes 1 piston, floating caliper 4 pistons, fixed caliper Brake disc [mm] 396 x 26 380 x 28 Parking brake electro¬ mechanical mechanical Further information on the M Carbon ceramic brake can be found in the " ST1216 M Carbon Ceramic Brakes" training material available in TIS and ICR A For necessary service work the current information and specifications in the documents in the Integrated Service Technical Application (ISTA) must be observed in each case. Dynamic Stability Control (DSC) The MK 100 from Continental is used as a Dynamic Stability Control (DSC) system. The characteristic maps of the DSC are M-specific and adapted to the respective brake system M Compound or M Carbon ceramic brake. Modification to brake pad wear monitoring Similar to the E82 M Coupe and the FI 0 M5, the F80/F82 only has one brake pad wear sensor on the left at the front axle. The second is at the rear axle on the right. 78 F80/F82 Complete Vehicle 5. Chassis and Suspension 5.3.2. Wheels/tires Summer equipment Index Explanation A 18" 513M standard wheel B 19" 437M wheel, optional equipment in two color variants The following wheel/tire combinations are offered: Standard equipment Designation E9x M3 F10M5 F80/F82-M3/ M4 Coupe LM EH2+ wheel rim, standard wheel, front (forged) 8.5x18 IS 29 9J x 19 IS 32 mm 9J x 18 IS 29 Styling 513M LM EH2+ wheel rim, standard wheel, rear (forge) 9.5x18 IS 23 10 J x 19 IS 34 mm 10J x 18 IS 40 Styling 513M Standard tires, front (Michelin Pilot Super Sport) 245/40 ZR 18 265/40 ZR 19 255/40 ZR 18 Standard tires, rear (Michelin Pilot Super Sport) 265/40 ZR 18 295/35 ZR 19 275/40 ZR 18 Optional equipment Designation F80/F82-M3/M4 Coupe LM EH2 wheel rim, front (forged) styling 437M 9J x 19 IS 29 LM EH2 wheel rim, rear (forged) styling 437M 10J x 19 IS 40 Tires, front (Michelin Pilot Super Sport) 255/35 ZR 19 Tires, rear (Michelin Pilot Super Sport) 275/35 ZR 19 The components of the above-listed wheel/tire combinations have been developed especially for the F80/F82. This can be recognized by the star on the outer side of the tire, among other things. 79 F80/F82 Complete Vehicle 5. Chassis and Suspension Other combinations may have a negative effect on the performance and the drivability of the F80/F82 and lead to forfeiture of the operating licence with forfeiture of the insurance coverage. 5.4. Dynamic handling control systems The M-specific coordination of the driving dynamics (longitudinal, transverse and vertical) was done on the Nurburgring Nordschleife. The main criteria were handling and the lap times. 5.4.1. Vertical Dynamics Management For vehicles with a M sports suspension (SA 2VF) the Electronic Damper Control (EDO) is installed. Here four continuously adjustable shock absorbers with coupled rebound/compression stage adjustment produce damping forces according to requirements. Through the use of forged aluminum dampers, the weight of the M sports suspension in the M3/ M4 Coupe was able to be reduced by about 5.5 kg when compared to the adaptive chassis and suspension in the F3x M3. Therefore the M sports suspension also contributes to the consistent lightweight construction concept of the new M3/M4 Coupe. The EDC function integrated in the M Vertical Dynamics Management control unit (M VDM) controls the adjustable dampers. The vehicle’s drivability can be influenced with regards to driving dynamics via the M sports suspension (EDC) button in the driving dynamics button panel at the center console. The program selection can also be pre-configured in the MDrive menu and selected via the corresponding M button on the steering wheel. 80 F80/F82 Complete Vehicle 5. Chassis and Suspension System overview F80/F82 system overview of EDC Index Explanation 1 Electronic adjustable damper, rear 2 VDM control unit 3 Wheel acceleration sensor, front 4 EDC button 5 Electronic adjustable damper, front 6 Wheel acceleration sensor, rear 81 F80/F82 Complete Vehicle 5. Chassis and Suspension System wiring diagram F80/F82 system wiring diagram of EDC 82 TF14-0454 F80/F82 Complete Vehicle 5. Chassis and Suspension Index Explanation 1 Vertical wheel acceleration sensor, front left 2 Electromagnetic adjusting valve, front left 3 Dynamic Stability Control (DSC) 4 Electromagnetic adjusting valve, front right 5 Vertical wheel acceleration sensor, front right 6 Power distribution box, luggage compartment 7 Vertical wheel acceleration sensor, rear right 8 Electromagnetic adjusting valve, rear right 9 Electromagnetic adjusting valve, rear left 10 Vertical wheel acceleration sensor, rear left 11 Vertical Dynamics Management (VDM) 12 Integrated Chassis Management (ICM) 13 EDC button 14 Front Electronic Module (FEM) Terminal 30 Terminal 30 Terminal 15N Ignition (after-run) System function The Electronic Damper Control (EDC) is a variable, electronically controlled shock absorber adjustment system that controls the vertical dynamics of the vehicle. The front axle damper and rear axle damper can be controlled independent of each other. The EDC adapts the damping forces of the shock absorber more or less instantly to the changing road or driving conditions. The Electronic Damper Control (EDC) is installed with the optional equipment SA 2VF "M sports suspension". The EDC consists of: • four continuously adjustable shock absorbers with coupled rebound/compression stage adjustment • the VDM control unit • two wheel acceleration sensors on the front axle to determine the wheel movement • two wheel acceleration sensors on the rear axle to determine the wheel movement • a sensor cluster integrated into the ICM control unit which determines the body movements (pitch, vertical, roll). 83 F80/F82 Complete Vehicle 5. Chassis and Suspension The sensors in the vehicle permanently measure: • the body and wheel acceleration • the current lateral and longitudinal acceleration • the vehicle speed • the steering wheel position Based on this measured data, the VDM control unit calculates the control commands to be sent to the electromagnetic valves in the shock absorbers for each individual wheel according to the road profile and driving situation. This means that the damping forces will always be applied according to the requirements. This improves ride comfort and also increases driving dynamics. This improves the vehicle's: • Suitability for long-distance journeys • Enhanced body stability and agility • Improves driving safety by minimizing wheel load fluctuations and reducing the stopping distance. M sports suspension (EDC) button option The button obtains its ground from the ICM and sends back a ground signal upon actuation to the ICM. The ICM forwards this information on the FlexRay data bus to the M VDM. In the F80/F82 Electronic Damper Control there are options "Comfort", "Sport" and "Sport+". All three programs have dynamic control in the F80/F82. Note: In the first E92/E90 M3 models the EDC had the three options, "Comfort", "Normal" and "Sport", whereby with the "Sport" option there is no dynamic control, but the dampers are set very hard. This is primarily suited for a cone slalom on an even surface. However, the fastest possible times on normal roads cannot be achieved with the "Sport" option. The E93 M3 was dynamically controlled from standard production in "Sport" mode, as well as in all subsequent models in the FI 0 M5, FI 2/FI 3 M6 and the F06 M6 in "Sport+" mode. Program description • "Comfort" emphasizes the comfortable design in the F80/F82 in order to satisfy the comfort requirements of a M3/M4 Coupe customer. The damper hardness is set to comfortable. • "Sport" supports a dynamic and sporty driving style with increased damper hardness. • "Sport+" in the F80/F82 means that dynamic control now also takes place here, whereby the damper hardness is increased further in comparison to "Normal". It may therefore also be the best selection for the fastest times on different route profiles on very even surfaces, unlike a route profile similar to a "cone-lined slalom". 84 F80/F82 Complete Vehicle 5. Chassis and Suspension 5.4.2. Transverse dynamics management Integrated Chassis Management The ICM is the transverse dynamics system network. This control unit coordinates the interaction between the M Servotronic (EPS), DSC, M sports suspension, engine control, M DCT and the regulated rear axle differential lock (GHAS). 5.4.3. Longitudinal dynamics management The LDM is performed by the DSC. The DSC MK 100 from Continental is used in the F80/F82. M dynamic mode and DSC OFF mode In M dynamic mode (MDM) the control threshold of the brake interventions is expanded/raised and the engine power reduction by the ASC is applied significantly later. This enables driver-oriented dynamic and sporty drivability. The "DSC" driving dynamics button or the configuration in the MDrive menu is used to switch between "DSC ON", "MDM" and "DSC OFF". The button obtains its mass from the ICM and sends back a mass signal upon actuation to the ICM. The ICM forwards this information on the FlexRay data bus to the DSC. 85 F80/F82 Complete Vehicle 6. General Vehicle Electronics 6.1. Voltage supply 6.1.1. Overview For the first time the voltage supply in a BMW M vehicle, an energy storage device other than the lead-acid battery is used. In the new F80/F82 a li-ion starter battery is installed for the series launch, which supplies the vehicle electrical system with voltage. Depending on the structure and/ or the material used for the electrodes, li-ion batteries are subdivided. In this case it is lithium-iron phosphate. The outer appearance of the li-ion starter battery does not differ from a normal starter battery, all components of the li-ion starter battery are located in the same housing. All other functions and components of the voltage supply are based on the F3x. Further information can be found in the Training Reference Manual ST1311 F30 Complete Vehicle. F80/F82 li-ion starter battery 6.1.2. Advantages The following advantages come with the use of a li-ion starter battery, which were decisive for the use of this technology in a high-performance vehicle like the F80/F82: • Weight saving: Also here in the area of the starter battery the concept of the intelligent lightweight construction in the new F80/F82 was pursued. With the use of the li-ion starter battery the weight of the starter battery was able to be reduced by about 12.5 kg. The li-ion starter battery only weighs 14 kg in comparison to a conventional AGM 90 Ah battery with about 26.5 kg. • C0 2 saving: A C0 2 saving can be achieved with a higher automatic engine start/stop function (MSA) availability. With a conventional lead-acid battery the regeneration capacity is not as high as with a li-ion battery as a result of the intelligent generator control. The li-ion starter battery can absorb considerably higher currents in a shorter time for charging in comparison to the lead- acid battery. This makes it ideal for use in vehicles with intelligent generator control (IGR). 86 F80/F82 Complete Vehicle 6. General Vehicle Electronics Life cycle: The number of available full cycles for li-ion battery is 14 times higher than for a conventional lead-acid battery. The li-ion battery is therefore the optimal alternative for use of the automatic engine start/stop function (MSA) in conjunction with the intelligent generator control (IGR). The battery life is also about twice as high as the traditional lead-acid battery. Maintenance-free: Maintenance-free, as no maintenance is required after topping up with distilled water (not with AGM batteries). Ideal voltage level: With the use of lithium iron phosphate cells (LiFePO^, which have a nominal voltage of 3.3 V per cell, a nominal voltage of the li-ion starter battery of 13.2 V could be achieved. Very high intrinsic safety: Lithium iron phosphate cells (LiFePO^ generally have an even lower hazard potential than other lithium-based batteries. 6.1.3. Comparison of li-ion starter battery/lead starter battery Designation Unit Lead-acid battery/ AGM battery Li-ion battery Nominal voltage [V] 12 13,2 Cell voltage [V] 2 3,3 Rated capacity [Ah] 90 69 Number of cells [Quantity] 6 4 Weight [kg] 26,5 14 Possible charging cycles [Quantity] about 350 about 5.000 Charging end voltage Ideal/Maximum [V] 14,2/16 14.4/temperature- dependent Discharging No total discharge protection/ battery damage Total discharge protection at 8 V Battery sensor Intelligent battery Battery system sensor (IBS) supervision circuits (BUE) in battery Housing [DIN] LN5 LN5 Ventilation Standard DIN housing with ventilation line Standard DIN housing with extended ventilation line (18.5 mm) Application range Every vehicle Only in the F80/F82 87 F80/F82 Complete Vehicle 6. General Vehicle Electronics 6.1.4. Structure of the li-ion starter battery External structure F80/F82 li-ion battery, external view Index Explanation 1 Ventilation connection 2 Positive terminal 3 Battery housing 4 Holder 5 Negative terminal 6 LIN connection 88 F80/F82 Complete Vehicle 6. General Vehicle Electronics Inner structure F80/F82 li-ion battery h- Index Explanation 1 Inner structure 2 Battery supervision circuits (BUE) with precision resistor 3 Metal ventilation chute 4 Electronic disconnect switch (2 relays) 5 Four li-ion battery cells 89 F80/F82 Complete Vehicle 6. General Vehicle Electronics 6.1.5. Function In addition to the four cells, there are also electronics and a battery isolating switch (2 relays) in the housing of the battery. Integrated electronics "Battery supervision circuits" The integrated electronics, the so-called battery supervision circuits (BUE), are responsible for the: • Communication via LIN data bus with FEM/DME • Diagnostics • Wake-up function via FEM via LIN data bus • Current monitoring of the individual cells and battery • Closed-circuit current monitoring • Voltage monitoring of the individual cells and battery • Cell voltage adaptation with counter function via passive system (resistance) • Startability monitoring • Temperature monitoring with resulting temperature model • Internal resistance monitoring • State of charge monitoring • Battery condition monitoring • Battery capacity monitoring • Data memory for battery information • Activation of the battery isolating switch in the event of a fault. The battery supervision circuits use the plug connection of the IBS. This is why there is no IBS installed in the F80/F82. All functions of the IBS are assumed in the F80/F82 by the battery supervision circuits. The battery supervision circuits cannot be replaced separately and are only offered together with the battery. Battery isolating switch The battery isolating switch (relay) is present twice, whereby it is a redundant system. This means in the event of failure of one switch (relay) the second battery isolating switch (relay) assumes the task. The battery isolating switch is activated by the battery supervision circuits and is responsible for protecting the li-ion cells from external and internal influences in the event of a fault. The following parameters may have effects on the position of the battery isolating switch: • Voltage • Current • Temperature 90 F80/F82 Complete Vehicle 6. General Vehicle Electronics The following table illustrates the possible positions of the electronic disconnect switch: Position Voltage Current Temperature Battery . Over isolating voltage switch open • Under voltage • Charge current too high • Short circuit current. • Temperature over 80 °C (176 °F). Battery normal isolating switch closed normal normal The battery isolating switch cannot be replaced separately and is only offered together with the battery. 6.1.6. Actions in the event of a fault Cause Impact and effects Measure Overloading Battery isolating switch opens. Remove voltage source. Battery isolating switch closes again after voltage drop. Total discharge below 8 V for over 60 seconds Battery isolating switch opens. Connect charger/Jump-start. Battery isolating switch closes again after voltage detection. Gas emission (cell fault, misuse) Smoke formation A Remove people from danger area. Provide fresh air. Replace battery. Replace ventilation hose. Caution: Risk of burning! Caution: Hazardous gases. External impacts and effects Damage to housing, poss. mechanical cell damage or damage to internal components. Replace battery and dispose of battery properly. Gas emissions with ignition source over 500 °C Gas ignites with corresponding concentration and ignition source. A Remove people from danger area. Provide fresh air. Inform fire brigade. Extinguish using a standard fire extinguisher. Replace battery if necessary. Caution: Risk of burning! Caution: Hazardous gases. Replace ventilation hose if necessary. 91 F80/F82 Complete Vehicle 6. General Vehicle Electronics ,e ® © ® © © © © 14,5 V /\ © 80 10 8 ® ® V 70 \/ 10 V ® ® Possible battery isolating switch positions Index Explanation V Voltage in volts A Current in A °C Temperature in degree Celsius A Battery isolating switch open B Battery isolating switch closed C Battery isolating switch open 1 Overvoltage-overload protection (cell voltage > 4 V/battery voltage > 16 V) 2 Undervoltage-total discharge protection (cell voltage < 2 V/battery voltage < 8 V after 30 seconds) 3 Overvoltage removed (battery voltage < 14.5 V for 2 seconds) 4 Charging voltage applied (battery voltage > 10 V for 2 seconds) 5 Charge current from charger too high 6 Short circuit current 7 Terminal voltage < Module voltage (for > 2 seconds) 8 Charging voltage applied 9 Temperature > 80° Celsius 10 Temperature < 70° Celsius 92 F80/F82 Complete Vehicle 6. General Vehicle Electronics A_ If the voltage falls below 8 V and the battery isolating switch opens, this becomes noticeable by a vehicle electrical system without voltage. Electrical functions are therefore no longer available. In this case the battery should not be replaced straight away as an initial measure. It is generally sufficient to recharge the battery. As soon as the battery supervision circuits detect a voltage over 10 V for longer than 2 seconds, the battery supervision circuits close the battery isolating switch again. The vehicle electrical system is supplied with voltage again. All electrical functions are available again. The battery is then charged again. The battery only has to be replaced if the battery isolating switch no longer closes or the energy diagnosis specifies a replacement. Refer to SIB 04 06 14 for more information. 93 F80/F82 Complete Vehicle 6. General Vehicle Electronics 6.1.7. System wiring diagram F80/F82 Voltage supply 94 TE14-0184 F80/F82 Complete Vehicle 6. General Vehicle Electronics Index Explanation 1 Power Distribution Module (PDM) 2 Alternator 3 Digital Motor Electronics DME 4 Starter motor 5 Electric fan 6 Relay for electric fan 7 B+jump start terminal point 8 Power distribution box, front 9 Power distribution box, engine compartment 10 Front Electronic Module (FEM) 11 Rear Electronic Module (REM) 12 Power distribution box, luggage compartment 13 Safety battery terminal (SBK) 14 Li-ion starter battery 15 Battery supervision circuits (BUE) 16 Battery power distribution box 17 Crash Safety Module (ACSM) Terminal 30 Terminal 30 Terminal 30B Terminal 30 basic operation Terminal 15N Ignition (after-run) Terminal 30F Terminal 30, fault-dependent 6.1.8. Li-ion starter battery in Service Charging For charging the li-ion starter battery during Service chargers recommended by BMW with corresponding function software for li-ion starter batteries can be used. Software updates are available for the following battery chargers approved by BMW: • Deutronic 800 • Deutronic 1200 • Deutronic 1600 Please observe the operating instructions of the charger manufacturer. 95 F80/F82 Complete Vehicle 6. General Vehicle Electronics A The maximum charging voltage of the li-ion batteries cannot be exceeded. Therefore, use chargers recommended by BMW with the corresponding function software for li-ion starter batteries. The charge current at low temperatures must be restricted. The li-ion starter battery is damaged by excessive charge currents at low temperatures. Therefore, use chargers recommended by BMW with the corresponding function software for li-ion starter batteries. Replacement In each case the current repair instructions in the Integrated Service Technical Application (ISTA) must be observed. Disposal Information on the disposal of the li-ion starter batteries is available from your respective Environmental Officer. General handling of li-ion starter battery Instructions on the handling of li-ion starter battery is available in the safety datasheet. A For necessary service work the current information and specifications in the documents in the Integrated Service Technical Application (ISTA) must be observed in each case. 96 F80/F82 Complete Vehicle 6. General Vehicle Electronics 6.2. Bus overview 97 TE14-0185 F80/F82 Complete Vehicle 6. General Vehicle Electronics Index Explanation 1 Control units with wake-up authorization 2 Start-up node control units for starting and synchronizing the FlexRay bus system ACSM Advanced Crash Safety Module (ACSM) ASD Active Sound Design AMPT Top HiFi amplifier COMBOX Combox (Combox emergency call, Combox Multimedia) CON Controller D-CAN Diagnosis-on-Controller Area Network DME Digital Motor Electronics DSC Dynamic Stability Control DVDC DVD changer EKPS Electronic fuel pump control Ethernet Cable-based data network technology for local data networks FEM Front Electronic Module FLA High-beam assistance FlexRay FZD Fast, preset and fault-tolerant bus system for use in automotive sector Roof function center GHAS Regulated differential lock HEADUNIT Headunit (Headunit High (HU-H) or Headunit Basis HU-B)) ICM Integrated Chassis Management IHKA Integrated automatic heating / air conditioning K-CAN Body controller area network K-CAN2 Body controller area network 2 KAFAS Camera-based driver support systems KOMBI Instrument cluster (MOST only with SA 6WA) M DKG M Double-clutch Transmission (M DCT)* MEPS M Servotronic (EPS) Electronic Power Steering (electromechanical power steering) MGWS M gear selector switch MOST Media Oriented System Transport M VDM M Vertical Dynamics Management OBD On-board diagnosis (diagnostic socket) PDC Park Distance Control (with SA 5DP, Parking Maneuvering Assistant: integrated in the Parking Maneuvering Assistant control unit, otherwise integrated in the Rear Electronic Module control unit) 98 F80/F82 Complete Vehicle 6. General Vehicle Electronics Index Explanation PMA Parking manoeuvring assistant PT-CAN Powertrain controller area network PT-CAN 2CAN2 Powertrain controller area network 2 RAD Radio RDC/TPMS Tire pressure monitoring system (only for US version) REM Rear Electronic Module REMAFA Reversible electric-driven reel, left REMABF Reversible electric-driven reel, right SMFA Seat module, driver SWW Lane change warning TRSVC Control unit for all-round vision cameras VM Video Module (Not for US) ZGM Central gateway module A__ * The M DKG (M Double-clutch Transmission) is referred to as M DCT in the US market due to a marketing decision. The following deviations exist in comparison to the standard F3x: PT-CAN The S55B30T0 engine exclusively obtains the DME variant MEVD17.2.G. In place of the electronic transmission control (EGS) the M Double-Clutch Transmission Drivelogic (M DKG/M DCT) is used and instead of the gear selector switch (GWS) the M gear selector switch (GWS) with Drivelogic button is used. FlexRay The regulated rear axle differential lock (GHAS) is also new. K-CAN Active Sound Design (ASD) is new. The trailer module (AHM) is deleted. MOST There is no difference to the current F3x vehicle electrical system. 99 F80/F82 Complete Vehicle 6. General Vehicle Electronics 6.3. On-board information 6.3.1. MDrive menu The MDrive menu can be found in the Settings menu. There are two individually adjustable M Drive configurations, M Drivel and M Drive2. The settings performed there are called up by pressing the corresponding button of the two available M buttons on the multifunction steering wheel. F80/F82 MDrive button Index Explanation 1 Ml Button 2 M2 Button 100 F80/F82 Complete Vehicle 6. General Vehicle Electronics There are two M buttons on the steering wheel thus enabling two different settings to be saved and called up. The activation of an MDrive configuration is displayed by an Ml or M2 symbol in the instrument cluster. The corresponding symbol flashes if for example ABS or DSC adjust upon activation of request. A renewed activation is only possible if the control is completed. F80/F82 MDrive combination display During the journey a requested configuration can be temporarily changed at any time until "Ignition OFF". The corresponding driving dynamics button must be operated. The Ml or M2 symbol in the instrument cluster goes out. An efficient/comfortable configuration is set by default in the factory for the Ml button and a sporty configuration for the M2 button. This setting can be adapted in the MDrive menu to the customer's needs and also reset again to the factory setting. Each M button is individually configurable and the overall configuration is also assigned to the vehicle remote control being used. If the DSC selection "MDM" or "DSC OFF" is chosen, a repeated, i.e. second operation, of the corresponding M button is required for activation of the configuration for approval reasons. F80/F82 MDrive menu, DCS confirmation 101 F80/F82 Complete Vehicle 6. General Vehicle Electronics A _ _ New approval requirements require an additional confirmation, if the MDrive configuration includes "DSC MDM" or "DSC OFF". The following functions and configurations can be selected and set: Dynamic Stability Control (DSC) • ON • MDM • OFF Engine dynamics control incl. ASD (Active Sound Design) • Sport + • Sport • Efficient Electronic Damper Control • Sport + • Sport • Comfort M Servotronic (EPS) • Sport + • Sport • Comfort Head-Up Display • M view • Unchanged Drivelogic • Drivelogic program "S" switch position (bar) 1 -3 • Drivelogic program "D" switch position (bar) 1 -3 102 F80/F82 Complete Vehicle 6. General Vehicle Electronics Configuration quick save A modified M setting or a new M setting using the drive dynamic buttons can be assigned to one of the two M buttons on the steering wheel Ml or M2. The corresponding M button on the steering wheel must be pressed and held for two seconds. The current configuration is set and overwrites any previously saved settings. This allows quick saving without accessing the M Drive menu. A_ If the driver is not aware that holding down the M button overwrites the current configuration/setting, this may lead to an unjustified customer complaint. Active configuration The individual driving stability controls can be set by the driver (while driving) using the assigned buttons. Then one of the two M buttons on the steering wheel can be pressed and held for 2 seconds to save the current configuration. 103 F80/F82 Complete Vehicle 6. General Vehicle Electronics 6.3.2. M instrument cluster The M instrument cluster is based on the instrument cluster high version from the F3x. The respective scales of the instrument cluster are market- and vehicle-specific. The following M-specific changes exist in comparison to the F3x: Round instruments: • Speed and engine speed display correspond to the drive concept (200 mph in 20 mph increments and 8,000 rpm). • Typical M red needle, lighting of the dial in white (also during the day without driving light), M inscription. F80/F82 instrument cluster M-specific displays: • MDM M dynamic mode symbol in place of the DTC • Ml = M Drivel • M2 = M Drive2 • Display of gear • Display of Drivelogic (bar symbol such as a button) • Display of system status: engine dynamics, damper control and Servotronic In the instrument cluster the current configuration of the engine dynamics, damper control and Servotronic systems is shown in the bottom part of the rev counter field. This function can be activated under Settings in the Configuration menu display. 104 F80/F82 Complete Vehicle 6. General Vehicle Electronics The confirmation of the MDrive settings for DSC, engine dynamics, transmission, EDC and Servotronic is also done centrally in the instrument cluster. For setting/adjustment work in the engine dynamics, EDC and Servotronic systems the response of the button activation is also done as a list in the instrument cluster. 6.3.3. Head-Up Display The optional color head-up display, depending on the national-market version, can switch to the M-specific display. The following information/parameters can be shown: • Shift point indicator by Shift-light function • Engine speed over rev counter range • Transmission shift level • Vehicle speed • Speed limit information (optional equipment) • Warnings same as F3x F80/F82 Head-Up Display The M-specific display for corresponding configuration in the MDrive menu is activated via the M button on the steering wheel or by selecting it from the Head-Up configuration menu. 6.3.4. Active Sound Design The Active Sound Design (ASD) is described in a separate Technical Reference Manual ST 1204 Active Sound Design. 105 F80/F82 Complete Vehicle 6. General Vehicle Electronics 6.3.5. M Lap Timer app This free app is an add-on for ambitious driving on the race track and enables precise analysis of the personal driving style. The smartphone with the installed BMW M Lap Timer app is connected to the vehicle via a USB cable or the appropriate snap-in adapter. The BMW M Lap Timer app not only records acceleration, braking points, lap times and high forces. The data is prepared in the form of graphics, the journey is played back with the real values as a virtual test drive. In addition, the journeys of different drivers can be analyzed and compared. 106 F80/F82 Complete Vehicle 7. Brief Overview of Equipment 7.1. F80/F82 standard equipment • M TwinPower turbo engine and M engine dynamics button • M instrument cluster • MDrive menu • M dynamic mode (MDM) with symbol button • M Servotronic (EPS) • M bucket seats for driver and front passenger with integrated head restraints and M moulding in the shoulder region illuminates the front, center console including armrest, armrests of doors in leather • M interior trim finishers • M leather steering wheel with two M multifunction buttons • M side gill, M door sill cover strip, M driver footrest • M3/M4 Coupe Aerodynamic package: Front and rear bumpers, front fender with extensions and gills, exterior mirror, side sill, adapted wheel arches at rear and front • M3/M4 Coupe inscription at the rear-wheel drive, front grill and in the gills • M exhaust tailpipe, right and left, double, round, chromium-plated • M BMW light-alloy wheels, double spoke, 513M, 18" currently with Michelin Pilot Super Sport mixed tires • Combined allover heat/sun protection glazing • M4 Coupe-specific trunk lid • M3-specific rear spoiler 7.1.1. Paint colors • Alpine White • Mineral White metallic • Silverstone metallic • Mineral grey metallic • Black sapphire metallic • Yas Marina blue metallic • Sakhir orange metallic • Austin yellow metallic 107 F80/F82 Complete Vehicle 7. Brief Overview of Equipment 7.1.2. Leather colors • Silverstone grey • Sakhir Orange • Sonoma Beige • Black • BMW Individual leather trims 7.1.3. Interior trims • Aluminium Blade • Blue Shadow • Carbon • Fine-line Anthracite wood trim • BMW Individual interior trims 108 Bayerische Motorenwerke Aktiengesellschaft Qualifizierung und Training RontgenstraBe 7 85716 UnterschleiBheim, Germany