Table of Contents E65 Trunk Lid Lift Subject Page Introduction .3 System Overview.3 Components.4 HKL Control Unit.4 Hydraulic Assembly.5 Trunk Lid Angle Sensor .6 Trunk Lid Button S237 (inside of the trunk lid) .6 Principle of Operation .7 Sequence of Opening Operation .7 Sequence of Closing Operation .8 Anti-Trap.8 Timed Arrest.8 Emergency Mode .8 Initial Print Date: 12/04 Revision Date: E65 Trunk Lid Lift (HKL) Model: E65/E66 Production: All After completion of this module you will be able to: • Understand the operation of HKL • Locate and identify HKL components 2 E65 Trunk Lid Lift Introduction The Automatic Trunk Lid Lift (HKL) is equipped on E65s ordered with the optional con¬ venience package. It controls automatic opening and closing of the trunk lid using a hydraulic pump and piston. The HKL control unit operates closely in conjunction with the Power Module and the CAS. Operation of the automatic trunk lid lift is only active while the vehicle is stationary. System Overview CAS SMFA SMBF TMFAT TMBFT TM FATH TM BFTH SMFAH SMBFH HKL PM AHM PDC RDC CIM LM DWA CON BZM RLS SHD SH BZMF WIM J CD 1 1 Kombi CDC T t ASK AVT 1 1 TEL LOGIC 7 1 1 VM svs t- NAV ^ D-BUS SZL SFZ SASL SASR ARS EMF STVL SSFA SIM STVR DME GRS SSBF EGS DSC SBSl SBSR EDC-K SSH PT-CAN 3 E65 Trunk Lid Lift K-CAN P K-CAN S MOST byteflight Components The HKL system consists of the following components: • HKL control unit • Hydraulic assembly (Pump, pressure valve, lines and piston) • Trunk lid angle sensor • Trunk lid button S237 TOEHKK (inside the trunk lid) The components and principle of operation of the trunk locking system remain unchanged from a conventional trunk . HKL Control Unit The HKL control unit controls the automatic opening and closing of the trunk lid. It operates in conjunction with the CAS and the PM (Power Module) and is networked in the K-CAN P-Bus. The HKL is located in the right rear corner of the luggage compartment. The Power Module controls the operation of the trunk lid lock and the soft close assem¬ bly as well as signalling (over the K-CAN P) the reguests for opening and closing the trunk from the external trunk button. The CAS provides the HKL with the reguest for opening the trunk from the Remote Control system as well as the passenger compartment trunk button. 4 E65 Trunk Lid Lift Hydraulic Assembly The hydraulic pump (radial piston) of the trunk lid lift is driven by an electric motor which operates in two directions of travel. The pump is located near the mount for the right rear strut. It is controlled via a PWM signal from the HKL control unit. The signal is varied depend¬ ing on the opening angle of the trunk lid to maintain an even closing speed over the entire range. An electro-mechanical hydraulic pressure valve is integrated into the hydraulic pump. The pressure valve is controlled by a PWM signal from the HKL control unit. The valve is normally open. The hydraulic pressure increases as the valve is powered closed. The hydraulic pressure, controlled by the PWM signal affects the trunk lid opening/clos¬ ing force. The maximum pressure produced by the hydraulic assembly is 10Obar. The hydraulic piston is attached to the left side trunk hinge. There is no initialization necessary when exchanging hydraulic components. The trunk should be operated several times to displace any air that may be in the system. 1. Hydraulic piston 2. Hydraulic lines 3. Pump assembly 3 p 5 E65 Trunk Lid Lift Trunk Lid Angle Sensor To detect the position, opening angle and speed of the trunk lid, an angle Hall sensor similar to those used on the E46 convertible is used. A voltage value is output depending on the opening angle of the trunk lid. The angle sensor is attached to the right side trunk hinge. The lid opening angle is divided into 9 segments. These segments are used to determine the reguired system pressure to maintain a steady opening/closing speed. Trunk Lid Button S237 (inside of the trunk lid) This button can only be accessed after the trunk lid is opened. It is a primarily used to signal the HKL to close the trunk, however it can signal both an open or close reguest. Input to the HKL control unit from this switch is a momentary ground signal. The ground is provided by the position contact inside of the trunk lock actuator (ZV) only when the trunk is “open”. An illuminated switch indicates that there is a ground available. 6 E65 Trunk Lid Lift Principle of Operation Sequence of Opening Operation When the "Open" request is sent by radio-control key or by a trunk button (TOEHK S117orTOEHKI S8), the PM operates the trunk lid lock actuator (ZV). The operating command is transferred by the K-CAN P to the HKL which activates the pump in the "Open" direction. The pressure valve is still not activated, so the pressure in the hydraulic system is minimal. When the trunk lid lock is fully open, the contact inside of the ZV signals the PM. This information is also transferred by bus to the HKL. Simultaneously as the SCA motor is being operated by the PM the HKL activates the opening operation. The pressure valve is closed and pressure is built up. The lid is now opened fully. The HKL module detects the position of the trunk lid using the angle sensor. Shortly before reaching the end stop "lid open" (transition from segment 7 to segment 8), trunk speed is reduced and the lid slowly moves to its end position. If one of the control buttons is pressed again during the opening sequence, the operation is interrupted. Pressing the button once more resumes the sequence. Operation of the automatic trunk lift is not allowed if the outside temperature (K-CAN P signal originated by the Kombi) is below -30°C (-22°F). 7 E65 Trunk Lid Lift Sequence of Closing Operation When the "Close" command is sent by pressing the control button (TOEHK S117 or TOEHKKS237 ), the HKL activates the closing operation. The pump motor is activated in the "closing" direction by reversing polarity in the HKL control unit. Shortly before the trunk lid reaches the closed position, the speed of the lid is reduced to provide a smooth run-down into the lock assembly. Once the contact switch in the trunk lock ZV opens, the SCA runs to bring in the trunk lid to the final closed position. Anti-Trap The trunk lid speed is reported to the HKL control unit by the angle sensor. The speed is compared with the time curve stored in the module. If this speed is slower then the stored value the trunk lid is stopped. Timed Arrest An timed arrest function prevents the pump motor from overheating: • If the pump is in continuous operation for 2 minutes it is shut-off for 6 minutes to allow it to cool. • The pump cannot be operated before the 6 minutes have elapsed. Emergency Mode If the automatic control malfunctions, the trunk lid can be opened and closed in the same way as a conventional, manually operated lid, i.e. without the need for additional mea¬ sures. Slightly more effort is reguired to open the trunk than for a gas-spring assisted lid. After manually opening the trunk lid, it should be opened and closed twice hydraulically. This process vents the hydraulic system again. 8 E65 Trunk Lid Lift - j j i Classroom Exercise - Review Questions 1. How does the HKL control unit control the speed of the trunk lid to provide a smooth rundown at the end positions (Fully open/closed)? 2. At what outside temperature is the HKL no longer operational? Where does this signal come from? Notes: 9 E65 Trunk Lid Lift