Table of Contents E70 Voltage Supply and Bus Systems Subject Page E70 Voltage Supply .5 System Circuit Diagram .6 Legend for System Circuit Diagram .7 Overview of System Components .8 Vehicle Battery.8 Distribution Box (on battery).8 Rear Distribution Box .10 Soldered Relays (in rear distribution box).11 Battery Cables.12 Front Distribution Box .13 Installation Position .13 Front Distribution Box and J unction Box Control Unit .14 Internal Plug Connection .15 Printed Circuit Board (PCB) .16 Soldered Relays .17 Direct Contacting .18 E70 Bus Systems .20 Structure in Vehicle.20 E70 Bus System Overview .21 E70 Overall Network .24 Overview of Bus Systems.24 Main Bus Systems.25 Changes to Main Bus Systems.25 Diagnosis CAN.26 Location of D-CAN Connector .27 Body CAN .28 MOST Bus System.30 Features .30 Control Channel .31 Synchronous Channel.31 Asynchronous Channel.31 Control Unit Logon .31 MOST Users .32 Light Direction.32 MOST Access.33 Initial Print Date: 10/06 Revision Date: 11/06 Subject Page Fiber Optics Connector.34 Identification of Fiber Optics Conductors .34 FlexRay .36 What are the advantages of FlexRay?.37 FlexRay - a standard in the automotive industry .37 FlexRay- Use in the E70 .38 System Overview .40 Properties of FlexRay .42 Bus Topology.42 Line-based Bus Topology .42 Point-to-point Bus Topology.42 Mixed Bus Topology.43 Redundant Data Transmission .43 Bus Topology of FlexRay in the E70 .43 Transmission Medium - Signal Properties.45 Deterministic Data Transmission .46 Bus Protocol .47 High Bandwidth .47 Synchronization.47 FlexRay in the E70.48 Wake-up and Sleep Characteristics .48 Wiring .49 Plug Connections.50 Sub-bus Systems .51 K-bus Protocol .51 LIN-bus.51 BSD.51 Terminating Resistors.52 Subject Page Voltage Supply and Bus Systems Model: E70 Production: From Start of Production After completion of this module you will be able to: • Describe E70 Bus Systems • Understand D-CAN • Understand FlexRay • Locate E70 voltage distribution components 4 E70 Voltage Supply and Bus Systems E70 Voltage Supply In view of the ever increasing electrical functions in the areas of vehicle comfort, communication and safety, growing significance is attached to the power supply system. In the E70, there are two separate distribution boxes. The front distribution box is near the glove box and the rear distribution box is on the right-hand side of the luggage compartment. The following graphic shows the arrangement of the most important components of the power supply system intheE70. Index Explanation 1 Rear distribution box, right-hand side of luggage compartment 2 Front distribution box behind glove compartment 5 E70 Voltage Supply and Bus Systems System C ircuit Diagram * 6 E70 Voltage Supply and Bus Systems Legend for System Circuit Diagram Index Explanation 1 Front distribution box, behind glove compartment 2 Rear distribution box, right hand side of luggage compartment 3 Safety battery terminal 4 Vehicle battery 5 Intelligent battery sensor (IBS) 6 Distribution box, on battery 7 Car Access System 3 (CAS 3) 8 J unction box control unit (J BE) 9 Digital Motor Electronic (DME) 10 Alternator 11 Starter KL30 Continuous B +(battery power) KL30g_f Switched positive (fault dependent) KL30g Switched positive, time dependent KL15 Ignition ON DME DM E main relay BSD Bit-serial data interface K-CAN BodyCAN PT-CAN Powertrain CAN 7 E70 Voltage Supply and Bus Systems Overview of System C omponents The power supply system of the E70 consists of the following components: • Vehicle battery • Distribution box on the battery • Rear distribution box on the right-hand side of the luggage compartment • Battery cables • Frant distribution box behind the glove compartment • J unction box control unit • E-box engine compartment • J ump start connection point • Alternator. The most important new features/changes to the power supply system in the E70 are described below Vehicle Battery The vehicle battery is installed on the rear right in the luggage compartment floor. The vehicle batteries are 70 Ah and 90 Ah batteries. Depending on the equipment, these batteries are AGM (Absorbent Glass Mat) batteries. The main advantage of the AGM battery is its higher cycle strength. Distribution Box (on battery) The distribution box in the luggage compartment of the E70 is mounted directly on the vehicle battery. The rear distribution box on the battery is secured on the vehicle battery by means of a metal tab. The metal tabs must be pressed downward and outward in order to release the distribution box. The distribution box on the battery is equipped with fuses for the following electric loads: • E lectrical auxiliary heater (100 A) • Valvetronic or common rail system (80 A) • Intelligent battery sensor IB S • Reserve • Front distribution box (250 A) • Rear distribution box (100 A) • Large electric fan 850 W (100 A) • Reserve. 8 E70 Voltage Supply and Bus Systems The distribution box on the battery should be replaced only as a complete unit. The fuses are integrated as a complete unit in the housing of the distribution box on the battery. The fuses differ in terms of their power rating. The distribution box additionally contains the powersupplyforthe IBS. Index Explanation 1 Battery cable to engine 2 Distribution box on battery 3 Intelligent Battery Sensor (IBS) Note: The connectors are color-coded and mechanically coded to avoid confu¬ sion. These are high power connections, therefore always ensure cor¬ rect contacting! When replacing or working on the distribution box, always make sure the plug connections and, above all, that the screw connections are secured properly. Connection between battery terminal and distribution box - 15 Nm. jy V V Index Explanation 1 Retaining clip 2 Connection to battery terminal 3 Rear distribution box connector 4 High current consumer connections 9 E70 Voltage Supply and Bus Systems Rear Distribution Box Due to the high number of consumers and control units in the E70, anotherfuse carrier has been mounted in the luggage compartment. In addition to the fuse carrier, relays are also plugged in or soldered onto the board. The following relays are accommodated in the fuse carrier: 1 ) 12 Index Explanation Index Explanation 1 Terminal 30g relay 2 Plug connector 10 E70 Voltage Supply and Bus Systems ■ Soldered Relays (in rear distribution box) Different relays are soldered onto the PCB in the rear distribution box. In the event of an error, the entire distribution box must be replaced. Index Explanation Index Explanation 1 Terminal 30 g_f relay 3 Terminal 15 relay 2 SCA relay 11 E70 Voltage Supply and Bus Systems Battery Cables On the E 70, two main power leads run along the underbody from the battery box to the engine compartment. One of the main power leads is routed via the jump start terminal to the starter and to the alternator. The other cable supplies the engine electronics with power. Depending on the model of vehicle, different line cross sections are used. Cable Cross section Material Cable to starter and alternator on N62 engine 110 mm2 Aluminum Cable to starter and alternator on N52 engine 90 mm2 Aluminum Cable to front distribution box behind glove box 35 mm^ Copper Cable to the motor electronics 10 mm^ Copper C able to electric fan 850 W 12 mm2 Copper One battery cable is installed in the vehicle interior. It runs to the front distribution box. The transfer points (magnified view) for the two main power cables is located in the battery box. To avoid damage, the main power cables are installed in a protected area on the underbody. 12 E70 Voltage Supply and Bus Systems Front Distribution Box This section describes the front distribution box. The junction box control unit is described in the section "J unction box control unit". There are three versions of front distribution boxforthe E70. In the lower part of the front distribution box, there is an opening through which it is connected to the junction box control unit. Installation Position The distribution box is installed underthe instrument panel on the right-hand side. To change a fuse, the distribution box must be lowered. 13 E70 Voltage Supply and Bus Systems Front Distribution Box and J unction Box Control Unit The connection between the front distribution box and the junction box control unit is realized via the opening in the bottom of the distribution box. An internal plug connection provides the electrical connection between the two components. When assembled, the two components from one unit consisting of the junction box control unit and the front distribution box. Note: The distribution box and junction box control unit components are to be replaced individually. In addition to the corresponding test modules in the diagnostics, diagnosis cables are also available with which electrical measurements can be made directly on the control-unit plugs and on the internal interface. 14 E70 Voltage Supply and Bus Systems ■ Internal Plug Connection The internal plug connection is on the left inside the opening forthe junction box control unit. The internal plug connection is responsible for actuating the relay in the front distribution box. In addition, the correct operation of this relay is monitored by the junction box control unit. Index Explanation Index Explanation 1 Monitoring connection 2 Actuation connection 15 E70 Voltage Supply and Bus Systems Printed Circuit Board (PCB) Different relays are used in the distribution box corresponding to the equipment and engine variants. Index Explanation Index Explanation 1 EHC relay 3 Relay for wiper stage 1 2 Rear wiper relay 16 E70 Voltage Supply and Bus Systems ■ Soldered Relays Different relays are soldered onto the PCB in the front distribution box. In the event of a fault, the entire distribution box must be replaced. Index Explanation Index Explanation 1 Terminal 30g relay 4 Relay for wiper stage 2 2 Heated rear window relay 5 Terminal 87 relay 3 Horn and headlight cleaning system double relay 17 E70 Voltage Supply and Bus Systems Direct Contacting On the distribution boxes, direct contacting to the fuses is carried out. The fuses are plugged into the PCB with a connection in the plug connector. The other plug connector is connected directly with the connectors on the wiring harness. The advantages of this design modification are: • Improved package space utilization • Improved heat dissipation Index Explanation Index Explanation 1 Front distribution box housing 3 Wiring harness connector 2 Fuse Note: Particular care must be taken to ensure thatthe fuses are fitted firmly when unplugging and re-connecting the connectors forthe wiring har¬ ness. The fuses must be braced when plugging in the wiring harness. 18 E70 Voltage Supply and Bus Systems 19 E70 Voltage Supply and Bus Systems E70 Bus Systems This reference information deals with the bus systems of the E70. The following innovations have been implemented in the bus systems in the new BMWX5 (E70): • New data transmission speed on the diagnostic CAN D-CAN (500 Kbps) • FlexRay- new bus system in the area of the chassis and suspension systems Structure in Vehicle The basic structure of the overall network in the E70 builds on the technological basis of the current E90. The drive train control units are linked through the powertrain-CAN (PT-CAN). In addition, the chassis-CAN (F-CAN) is used forthe chassis and suspension systems. The control units of the general vehicle electrical system are connected via the K-CAN. The MOST is the information carrier for the majority of control units in the area of information and communication technologies. A new addition is the FlexRay. This bus system is used forthe first time in the area of the chassis and suspension control systems. It is described in more detail in this reference information. 20 E70 Voltage Supply and Bus Systems E70 Bus System Overview 21 E70 Voltage Supply and Bus Systems Legend for E70 Bus System Overview Index Explanation Index Explanation ACSM Advanced Crash Safety Management EMF Electro-mechanical Parking Brake AS Active Steering EWP Electric Water Pump ARS Active Roll Stabilization FD Rear Compartment Display ASP Outside Mirror FKA Rear Compartment Heating and A/C CA Comfort Access FLA High Beam Assistant CAS Car Access System FRM Footwell Module CCC CarCommunication Computer FZD Roof Function Center CDC CD Changer GWS Gear Selector Lever CHAMP Central Head unit and Multimedia Platform HB3SR Heating/Ventilation 3rd Row CID Central Information Display HiFi HiFi Amplifier CON Controller HKL Tailgate Module DME Digital Motor Electronics HUD Head-up Display DSC Dynamic Stability Control IBOC In-Band On-Channel (HD Radio) DSC-SEN DSC Sensor IBS Intelligent Battery Sensor DVD Digital Video Disc Changer IHKA Automatic Heating and Air Conditioning EDC SHL Electronic Damper Control, rear left satellite JB J unction Box EDCSHR Electronic Damper Control, rear right satellite Kombi Instrument Cluster EDC SVL Electronic Damper Control, front left satellite OC-3 Seat Occupancy Sensor (US) EDC SVR Electronic Damper Control, front right satellite PDC Park Distance Control EGS Electronic Transmission Control QLT Oil Quality/Level/Temperature sensor EHC Electronic Height Control RFK Reversing Camera EKP Electric Fuel Pump (control unit) RLSS Rain/Driving lights/Solarsensor 22 E70 Voltage Supply and Bus Systems Legend for E70 Bus System Overview - Cont. Index Explanation Index Explanation RSE Rear Seat Entertainment BSD Bit-serial Data Interface SBFA Driver's Switch Cluster Crash-Sig Crash Signal SDARS Satellite Radio Control Unit D-CAN Diagnosis CAN SINE Siren and Tilt Sensor F-CAN Chassis CAN SMBF Passenger Seat M odule F lexRay FlexRay Bus System SMC Stepper Motor Controller K-Bus Body Bus SMFA Driver's Seat Module K-CAN BodyCAN SVBF Passenger's Seat Adjustment LIN-Bus Local Interconnect Network Bus SVFA Driver's Seat Adjustment LoCAN Local CAN SZL Steering Column Switch Cluster MOST Media Oriented Systems Transport TAGE Electronic Outer Door Handle Module MOST WUP MOST Wake-up Line TCU Telematics Control Unit PT-CAN Powertrain CAN TOP-HIFI Top Hi-Hi Amplifier WUP Wake-up Line TPM Tire Pressure Monitoring System CAS Bus Connection TPM-SEN Tire Pressure Control (TPM -Sensor) VDM Vertical Dynamics Management (EDC) VGSG Transfer Case Control Unit (VTG) WT Variable Valve Gear IHKA Stepper Motors Generator 23 E70 Voltage Supply and Bus Systems E70 Overall Network The overall network in the E70 consists of various bus systems that enable communica¬ tion between the individual control units. In view of the increasing interconnection of the control units, it is possible to use the sensors of one system throughout the network. The sensors are connected to the control unit that initially requires the information logic-based and virtually in real time. This information, however, can also be made available to other control units. Using the example of the vertical dynamics management (VDM), initially, the VDM control unit acquires the ride-height levels of the wheels. The dynamic headlight-range adjustment facility can also use this information for the purpose of adapting the beam height of the headlights. The VDM makes available the information via the corresponding bus systems to the footwell module. Apart from the FlexRay and the D-CAN, all bus systems in the E70 are already known from other BMW models. This section outlines all bus systems in the E70. This bus system is used for the first time for the data exchange in the area of the vertical dynamics management (VDM). It is used to exchange data between the VDM control unit and the EDC satellites. Overview of Bus Systems In principle, a distinction is made between two groups of bus systems: • Main bus systems • Sub-bus systems Main bus systems are responsible for the data exchange between the control units throughout the vehicle system. This includes system functions such as diagnosis, network management, programming and encoding. For example, when locking the doors in the E70,the status of the door contacts is read in via the footwell module. The information is transmitted via the K-CAN to the junction box control unit which in turn activates the central locking drive units. Sub-bus systems exchange data within one function group. For example, the data of the driver's door switch cluster are read in by the junction box control unit and forwarded to the footwell module. The connection provided between the driver's door switch cluster and junction box control unit is a sub-bus known as the LIN-bus. 24 E70 Voltage Supply and Bus Systems Main Bus Systems Main Bus System Data Rate Bus Structure D-CAN 500 Kbits/s Linear, two-wire K-CAN 100 Kbits/s Lineartwo-wire, single wire mode possible for emergency operation PT-CAN 500 Kbits/s Linear, two-wire F-CAN 500 Kbits/s Linear, two-wire FlexRay 10 M bits/s Star, two wire MOST 22.5 Mbits/s Ring, fiber optics ■ Changes to Main Bus Systems The most important changes to the main bus systems include. • Diagnosis CAN D-CAN now with modified data rate (500 Kbit/s) • FlexRay- new bus system in area of chassis and suspension control systems, vertical dynamics management (VDM). As before, the central gateway function is integrated in the junction box control unit. A further gateway that sends diagnosis jobs between PT-CAN and FlexRay is located in the VDM control unit. 25 E70 Voltage Supply and Bus Systems Diagnosis CAN After connecting a BMW diagnostic system, the gateway (junction box control unit) places the requests of the BMW diagnostic system on the internal buses. The responses undergo the same process in opposite direction. In future, a new communication protocol will be used for diagnosis. The D-CAN will replace worldwide the previous diagnostic interface and its protocol which is based on KWP 2000 (Keyword Protocol 2000). The reason for the changeover is a new legal requirement in the USA requiring that all vehicles be equipped with the D-CAN as from model year 2008. The transitional phase will begin in September 2006. The E70 will be one of the first vehicles equipped with D-CAN. This modification will then be phased-in on all BMW models. An optical programming system OPS or an optical testing and programming system OPPS as well as an OBD connection cable forthe OPS with following identification are required to perform diag¬ nostic procedures on these vehicles. O 4 vtO CAM included Made' : n German 26 E70 Voltage Supply and Bus Systems Location of D-CAN Connector The diagnosis socket is located underthe dashboard on the driver's side. D-CAN support with the diagnostic head is technically not possible. The following interfaces can be used: • OPS • OPPS OBD access in the vehicle will remain unchanged. The pin assignments are as follows: • 16 =Terminal 30 • 5=Terminal31 • 14+6 = Communication connections The diagnosis socket is located underthe dashboard on the driver's side. Kl. 30 Kk 31 D-CAN Low D-CAN High 27 E70 Voltage Supply and Bus Systems BodyCAN The known familiarCAN-bus systems are still used on the E70. In view of their distribution in the vehicle, the control units are linked at various nodal points. Several connections forthe K-CAN are provided not only in the wiring harness but also at the junction box control unit. Electrically, there is only one K-CAN. This means, from an electrical point of view, all linked control units are connected in parallel to the K-CAN. Physically, various control units are connected at nodal points or at one control unit, i.e. the junction box control unit. “1 ! | C1D tiT.ZV ■ k-J- hbaka r 1:0 t ¥ PM Ci1£> ft 3.-11« ' fihtOT 31 JTfcA CCk | |L_ FI A j rrn IIK£ : l: y :n.- J the ; ajiI t HKL : IK I -1! ± Index Explanation Index Explanation 1 K-CAN distributor 3 K-CAN 2 Optional equipment 28 E70 Voltage Supply and Bus Systems 29 E70 Voltage Supply and Bus Systems MOST Bus System Features of the MOST system MOST is a data bus technology for multimedia applications that was specifically developed for use in motor vehicles. MOST stands for "Multimedia Oriented System Transport". The MOST bus uses light pulses for the purpose of transmitting data and is based on a ring structure. The data are transmitted only in one direction in the ring. MOST technology satisfies two important requirements: 1. The MOST bus transports control data as well as data for audio, navigation and other services. 2. M OST technology provides a logical model for controlling the data variety and complexity, i.e.the MOST application framework. The MOST application framework organizes functions of the overall system. MOST is capable of controlling and dynamically managing distributed functions in the vehicle. An important characteristic of a multimedia network is that it not only transports control data and sensor data such as on the CAN-bus and LIN-bus for instance. In addition, a multimedia network can also transmit digital audio and video signals and transport graphics as well as other data services. Features • High data rate 22.5 Mbits/s • Synchronous/asynchronous data transmission • MOST assigns the control units to nodes in the bus • Fiber optics cables as transmission medium • Ring structure Each MOST control unit can send data on the MOST bus. Only the gateway control unit can initiate data exchange between the MOST bus and other bus systems. The control units, CHAMP and the car communication computer, are used as the gateway and mas¬ ter control unit. The data are transmitted on various channels on the MOST bus. Corresponding to the application, the data are sent to different time windows within the data flow (channels). 30 E70 Voltage Supply and Bus Systems Control Channel Control signals such as volume control for the Top HiFi amplifier and data for diagnosis purposes are sent via the control channel. Synchronous Channel The synchronous channel is mainly reserved forthe purpose of sending audio data. Asynchronous Channel The asynchronous channel transfers image data from the navigation system such as the direction arrows. The control channel and the asynchronous channel are used for programming the control units on the MOST bus and correspondingly adapt it to the MOST-direct access Index Explanation Index Explanation 1 Synchronous channel 3 Control channel 2 Asynchronous channel Control Unit Logon Precisely in the same way as on the E6xmodels, the control units installed on the MOST bus are stored in a registration file in the master control unit. The corresponding data are stored during the production process and, in connection with control unit retrofits, after programming the respective control unit. The control units and their sequence on the MOST bus are stored in this registration file. With the fiber optics connector, it is possible to connect control units in the rear area of the E70 after factory production or after a repair in different order. With the aid of the registration file, the BMW diagnosis system can determine the installed control units and their order. During their start-up procedure, all control units on the MOST bus send their identifier to the master control unit. In this way, the master control unit detects what control units are connected to the MOST bus. A corresponding fault location can be concluded in diagnosis if the login of one or several control units is not received. 31 E70 Voltage Supply and Bus Systems MOST Users In the E70,the MOST bus is usedforthe components in information/communication systems. The CCC,orthe CHAMP is used as the master control unit. Other bus users may be: • CD changer/DVD changer • Top-HiFi amplifier • Satellite tuner (SDARS), IBOC • Telephone • Head-up display (HUD) The following overview shows a possible equipment configuration. O Q U D □ HI l^_l 1=3 ■ C3 • 1=3- TCU 1 L -i TOP-H1 FI -f Index Explanation Index Explanation ccc CarCommunications Computer TOP- Hifi Top Hi-Fi amplifier TCU Telematics Control Unit 1 Fiberoptic connector Light Direction Data are always sent in one direction on the MOST bus. Each control unit can send data on the MOST bus. The physical light direction is from the master control unit (CHAM P, multi-audio system controller or car communication computer) to the fiber optics connector and from here to the control units in the luggage compartment (Top H iF i amplifier, CD-changeretc.). From the last control unit, the light returns via the MOST-direct access to the master control unit. 32 E70 Voltage Supply and Bus Systems MOST Access As on all vehicles equipped with a MOST bus system, direct MOST access is also provided on the E70. The direct MOST access is located on the right hand side underthe dashboard in the vehicle interior. A cover provides direct access to the MOST. The two connectors must be removed from the holder secured on the cover. The two connectors are then plugged together. The OPS/ OPPS can now be connected to the connector as usual. 33 E70 Voltage Supply and Bus Systems Fiber Optics Connector The use of the fiber optics connector provides the advantage of being able to easily retrofit control units in the area of the luggage compartment. The connector is located behind the left-hand cover next to the rear seat backrest. It is arranged in the MOST bus system between the front area (head unit, CDC and HUD) and the rear area of the vehicle (TEL etc.). One or two fiber optics connectors are installed corresponding to the equipment configuration. One is responsible for the factory-installed control units. The other is used for the preparations for options. A fiber optics connectorfor option preparations is installed only if option preparations are actually installed. The ends of the fiber optics conductors for options are always grouped together on the same row in the fiber optics connector to avoid damage to the ends of the fiber optics conductors. As soon as the retrofit is installed, the fiber optics connectors are reconnected according to instructions and integrated in the MOST bus. Identification of Fiber Optics Conductors The fiber optics conductors are identified at their ends making it is possible to identify the control unit from which the fiber optics conductor comes or goes. 34 E70 Voltage Supply and Bus Systems 35 E70 Voltage Supply and Bus Systems FlexRay In the future, driving dynamics control systems, driver assistance systems and their innov¬ ative interconnection will be evermore important for the differentiation of the BMW badge. Since today's networking systems using the CAN-bus have already reached their limit, it is necessary to find a suitable alternative for CAN. In co-operation with Daimler Chrysler AG and the semiconductor manufacturers Freescale (formerly Motorola) and Philips, BMW AG founded the FlexRay consortium in 1999 for the purpose of developing innovative communication technology. The consortium was soon joined by further partners, including Bosch and General Motors and to date, the Ford Motor Company, Mazda, Elmos and Siemens VDO have also decided to join. In the meantime, almost all significant car makers and suppliers throughout the world have joined the FlexRay consortium. Index Explanation 1 Real time capabilities, deterministic (strictly defined) and redundant 2 Conditional realtime capabilities - sufficient for control systems 3 No real time capabilities FlexRay is a new communication system which aims at providing reliable and efficient data transmission with real-time capabilities between the electrical and mechatronic components for the purpose of interconnecting innovative functions in motor vehicles, both today and in the future. 36 E70 Voltage Supply and Bus Systems Development of the new FlexRay communication system was prompted by the ever growing technological requirements placed on a communication system for interconnecting control units in motor vehicles and the realization that an open and standardized solution was needed for infrastructure systems. FlexRay provides an efficient protocol for real-time data transmission in distributed sys¬ tems as used in motor vehicles. With a data transmission rate of 10 M bits/s, the FlexRay is distinctly faster than the data buses used in the area of the chassis, drive train and suspension oftoday's motor vehicles. In addition to the higher bandwidth, F lexRay supports deterministic data transmission and can be configured such that reliable continued operation of remaining communication systems is enabled even in the event of individual components failing. What are the advantages of F lexRay? • High bandwidth (10 Mbits/s compared to 0.5 Mbits/s of the CAN) • Deterministic (= real-time capabilities) data transmission • Reliable data communication • Supports system integration • Standard in automotive industry ■ FlexRay - a standard in the automotive industry The FlexRay bus system is an industrial standard and is therefore supported and further developed by many manufacturers. merit Members l>*l J- L-iIl I . 'Irv.-jr.:- n El II Hn rrf| ^ M r ■ ■ ri Lyild’l e .l'Tjh £ I iJ- Associate Members TV-itt-j-kih l.hMIlJ WlUiA UtLfcbiV, 'i ■ I n *• i n 3 i.ara' a M.i-IitJ, TyrCO pl^rli nnic <* Corner alian Qote Member Krt ik ne T ■ KJA MOTORS □ MW Group Toyota Rer-nnlt Volkswagen PtiiNpa □jiifntCTOirysIrcr General Motors. EOich r.ll |All III HI , Honda Moboi t i. ElKI-- • ■ !■ ■■ UpwniwrJ I +wr._.tn j U"i T RirJP . KHEL-rfpr^-''*r H- Li &CiN Frnrr.c .i!r Semico -ductor i* 1 lYi-o fcJcocran : l^ord Motor Co^pony -Sn Pc upcot Citroon ■■ !H rnSLIJW hEirgilEnl r HI AT KM. TIN i'l’rr.'Liiln , L1 1 T.-,-:i4 Mu-hMIi. jrf.- ■ j'J■ III liliikLinnj ij n-Op-B-rri-: fn • "AmifiTJi- h-, •- i. i ■» L. H ij i v % i tJ LiitsCviwhiu fy(T-' * >piH 37 E70 Voltage Supply and Bus Systems FlexRay - Use in the E70 With the launch ofthe E70, the FlexRay bus system will be used forthe first time worldwide in a standard production vehicle. The FlexRay bus system establishes the connection between the VDM control unit (vertical dynamics management) and the EDC satellites at the shock absorbers. A detailed functional description ofthe overall system can be found in the reference information - "Vertical Dynamics Systems”. 38 E70 Voltage Supply and Bus Systems 39 E70 Voltage Supply and Bus Systems System Overview D-CAN PT-Can ■■ OBD VDM 40 E70 Voltage Supply and Bus Systems Legend for System Overview Index Explanation 1 J unction box control unit 2 Vertical Dynamics management (VDM) 3 Diagnosis connector 4 Ride height sensors, front 5 EDC satellites with vertical acceleration sensors and solenoid valves 6 Ride height sensors, rear D-CAN Diagnosis CAN F-CAN Chassis CAN PT-CAN Powertrain CAN FlexRay FlexRay bus system KL 30 g Terminal 30g 41 E70 Voltage Supply and Bus Systems Properties of FlexRay The most important properties of the FlexRay bus system are outlined in the following: • Bus topology • Transmission medium - signal properties • Deterministic data transmission • Bus protocol Bus Topology The FlexRay bus system can be integrated in various topologies and versions in the vehicle. The following topologies can be used: • Line-based bus topology • Point-to-point bus topology • M ixed bus topology Line-based Bus Topology All control units (SG1...SG3) in line-based topology are connected by means of a two-wire bus, consisting of two twisted copper cores. This type of connection is also used on the CAN-bus. The same information but with different voltage level is sent on both lines. The transmitted differential signal is immune to interference. The line-based topology is suitable only for electrical data transmission. Point-to- point Bus Topology The satellites (control units SG2...SG5) in point-to-point bus topology are each connected by a separate line to the central master control unit (SGI). Point-to-point topology is suitable for both electrical as well as optical data transmission. Line-based bus topology 42 E70 Voltage Supply and Bus Systems Point to point bus topology Mixed Bus Topology Mixed bus topology caters for the use of different topologies in one bus system. Parts of the bus system are line-based while other parts are point-to-point. ■ Redundant Data Transmission Fault-tolerant systems must ensure continued reliable data transmission even after failure of a bus line. This requirement is realized by way of redundant data transmission on a second data channel. A bus system with redundant data transmission uses two independent channels. Each channel consists of a two-wire connection. In the event of one channel failing, the information of the defective channel can be transmitted on the intact channel. FlexRay enables the use of mixed topologies also in connection with redundant data transmission. B us Topology of F lexRay in the E 70 The physical configuration of the FlexRay bus system in the E70 is point-to-point. All EDC satellites are individually connected via plug connections to the VDM control unit. Internally, however, the left and right EDC satellites are connected to form a line-based topology. The two lines are connected by means of a double point-to-point connection consisting of two bus drivers. Every item of information that is sent from one of the EDC satellites orfrom the central VDM control unit reaches all connected control units. Index Explanation A Channel 1 B Channel 2 43 E70 Voltage Supply and Bus Systems VDM System Schematic Index Explanation Index Explanation 1 Vertical Dynamics Management (VDM) 6 Bus driver 2 EDS satellites, front left 7 Terminating resistor 3 EDS satellites, front right 8 Microprocessor 4 EDS satellites, rear right F lexRay F lexRay bus system 5 EDS satellites, rear left 44 E70 Voltage Supply and Bus Systems Transmission Medium - Signal Properties The bus signal of the FlexRay must be within defined limits. A good and bad image of the bus signal is depicted below. The electrical signal must not enter the inner area neither on the time axis nor on the voltage axis. The FlexRay bus system is a bus system with a high data transmission rate and therefore with rapid changes in the voltage level. The voltage level as well as the rise and drop of the voltage (edge steepness) are precisely defined and must be within certain values. There must be no infringements of the marked "fields" (green and red hexagon). Electrical faults resulting from incorrect cable installation, contact resistance etc. can cause data transmission problems. Index Explanation Index Explanation A Good image B Bad image The images shown above can be depicted only with very fast oscilloscopes. The oscilloscope in the BMW diagnostic system is not suitable for representing such images. The voltage ranges of the FlexRay bus system are: • System ON - no bus communication 2.5 V • High signal - 3.1 V (voltage signal rises by 600 mV) • Low signal - 1.9 V (voltage signal falls by 600 mV) The voltage values are measured with respect to ground. 45 E70 Voltage Supply and Bus Systems Deterministic Data Transmission The CAN-bus system is an event-controlled bus system. Data are transmitted when an event occurs. In the event of an accumulation of events, delays may occur before further information can be sent. If an item of information cannot be sent successfully and free of errors, this information is continually sent until the communication partner confirms its receipt. If faults occur in the bus system, this "event controlled” information can back up causing the bus system to overload, i.e. there is a significant delay in the transmission of individual signals. This can result in poor control characteristics of individual systems. The FlexRay bus system is a time-controlled bus system that additionally provides the option of transmitting sections of the data transmission event-controlled. In the time controlled part, time slots are assigned to certain items of information. One time slot is a defined period of time that is kept free fora specific item of information (e.g. engine speed). Consequently, important periodic information is transmitted at a fixed time interval in the FlexRay bus system so that the system cannot be overloaded. Other less time-critical messages are transmitted in the event-controlled part. An exam¬ ple of deterministic data transmission is outlined in the following. U i 2 n e V xyz... abc... ..jultul „uiLn n junm jujjl t \m - & 46 E70 Voltage Supply and Bus Systems Index Explanation 1 Time-controlled part of cyclic data transmission 2 Event-controlled part of cyclic data transmission 3 Cycle (5 ms total cycle length of which 3 ms static (= time-controlled) and 2 ms dynamic (= event-controlled) n Engine speed < Angle t Temperature V Road speed xyz..abc.. Event-controlled information t Time Bus Protocol Deterministic data transmission ensures that each message in the time-controlled part is transmitted in real time. Real time means that the transmission takes place within a defined time. Therefore, important bus messages are not sent too late due to overloading of the bus system. If lost due to a temporary problem in the bus system (e.g. EMC problem) a message cannot be sent again. A current value is sent in the next assigned time slot. High Bandwidth The FlexRay bus system operates with a data transmission rate of 10 M bits/s. This speed corresponds to 20 times the data transmission rate of the PT-CAN. Synchronization A common time base is necessary in orderto ensure synchronous execution of individual functions in interconnected control units. Time matching must take place via the bus system as all control units operate with their own clock generator. The control units measure the time of certain synchronization bits, calculate the mean value and adapt their bus clock to this value. This system ensures that even minimal time differences do not cause transmission errors in the long term. 47 E70 Voltage Supply and Bus Systems FlexRay in the E70 The FlexRay bus system in the E70 is designed as a two-wire, single-channel bus system. Acting as the gateway, the VDM control unit establishes the connection between the PT-CAN and FlexRay bus systems. Data communication between the EDC satellites on the FlexRay and the other control units installed in the E70 takes place via the VDM control unit. Wake-up and Sleep Characteristics The control units are activated by means of an additional wake-up line. The wake-up line has the same function as the previous wake-up line (15WUP) in the PT-CAN. The signal curve corresponds to the signal curve of the PT-CAN. As soon as the bus system is woken, the VDM receives a High level on the PT-CAN and transfers this signal to the wake-up line of the FlexRay, thus also waking the satellites. 48 E70 Voltage Supply and Bus Systems The "wake-up voltage curve" graphic shows the typical behavior of the voltage curve in response to unlocking and starting the vehicle. Phase 1: Driver unlocks the car, the CAS control unit activates the K-CAN and the PT-CAN, the voltage level in the PT-CAN briefly goes to High, the VDM copies the signal and transfers it to the wake-up line on the FlexRay. Phase 2: Car is opened, terminal R is still OFF, the voltage levels in the bus systems drop again. Phase 3: Car is started, terminal 15 is ON, the voltages remain at the set levels until terminal 15 is turned off again. Phase 4: The complete vehicle network must assume sleep mode at terminal R OFF in order to avoid unnecessary power consumption. Each control unit in the network signs off to ensure that all control units "are sleeping". Only when all EDC satellites have signed off at the VDM control unit can this control unit pass on this information to the PT-CAN and therefore to the complete network. An error message is stored if this is notthe case. This error message is then evaluated as part of the energy diagnosis procedure. ■ Wiring The wiring of the FlexRay bus in the E70 is executed as a sheathed, two-core, twisted cable. The sheathing protects the wires from mechanical damage. The terminating resistors are located in the EDC satellites. Each satellite has one terminating resistor. Since the surge impedance (impedance of high-frequency lines) of the lines depends on external influencing factors, the terminating resistors are precisely matched to the required resistance. T he four sections of line to the satellites can be checked relatively easily by means of a resistance measuring instrument (ohmmeter, multimeter). The resistance should be measured from the VDM control unit. See BMW diagnostic system for pin assignments The following conclusions can be made: RBP-BM: cor = 10 Ohms - There is a short circuit in this section of line. RBP-BM: 10-90 Ohms - This section of line is damaged (e.g. moisture in connector, line pinched) RBP-BM: 90-110 Ohms - This section of line is OK and the satellite is connected (Note: Impedance errors are not recognized) RBP-BM: > 110 Ohms - There is a break in the line orthe satellite is not connected or there is a break in the connection to the satellites. 49 E70 Voltage Supply and Bus Systems Note: Measuring the resistance of the FlexRay lines cannot provide a 100% deduction in terms ofthe system wiring. In the case of damage such as pinching orconnectorcorrosion,the resistance may be within the toler¬ ance when the system is static. In dynamic mode, however, electrical influences can cause increased surge resistance, resulting in data transmission problems. Note: It is possible to repair the FlexRay bus. If damaged, the cables can be connected using conventional cable connectors. Special requirements, however, must be observed when reinstalling the system. The wiring ofthe FlexRay system consists of twisted lines. This twisted arrangement (transposition) should be retained as far as possible. Repaired areas with stripped insulation must be sealed again with shrink- fit tubing. Water can affectthe surge resistance and therefore the effi¬ ciency ofthe bus system. ■ Plug Connections The two plug connections contain the powersupply ofthe control units, the wake-up line and the bus connection with wake-up line. The connection to the satellites in the wheel arch is made with waterproof plugs. Two plugs are used: Terminal 30g Plug 1, black Terminal 31 Wake-up line Plug 1, blue FlexRay (green wire) F lexRay (pink wire) 50 E70 Voltage Supply and Systems Sub-bus Systems Sub-bus systems are known from the other BMW models. Main Bus System Data Rate Bus Structure K-Bus 9.6 Kb its/s Linear, single-wire LIN-Bus 9.6/19.2 Kbits/s Linear, single-wire BSD 9.6 Kb its/s Linear, single-wire K-bus Protocol The term "K-bus (protocol)" is used fora series of sub-bus systems in the bus overview. These sub-bus systems are used for various purposes. The K-bus protocol used here is a common component already used in predecessor models. The sub-bus is used in connection with the following systems: • Connection between SINE and FZD • Connection between ACSM and TCU • Electronic outer door handle module • Comfort Access • Seat adjustment switch on multifunction seat • EWS connection between CAS and DME+EGS (N52). LIN-bus The LIN-bus was used for the first time on the E46 for controlling the outside mirrors. The LIN-bus realizes the following connections in the E70: • Footwell module to driver's door switch cluster • Footwell module to outside mirrors High • Roof functions center to rain/driving lights/ solar sensor • Actuation of IH KA actuator motors • Footwell module to stepper motor controller • Connections between gear selector lever module and electronic transmission control BSD The bit-serial data interface BSD is still used on the E70. It makes the following connections from the engine management to the corresponding subsystems: • Intelligent battery sensor • Generator regulator • Oil condition sensor • Electric coolant pump 51 E70 Voltage Supply and Bus Systems Terminating Resistors Terminating resistors are used to ensure exact signal progression in the bus systems. These terminating resistors are located in the control units of the bus systems. Terminating resistors are located in each control unit connected to the K-CAN. In connection with the main bus systems F-CAN and PT-CAN, terminating resistors are always located only in two control units on the bus. The terminating resistors in the F-CAN are located in the control units: • Steering column switch cluster • Dynamic stability control The terminating resistors in the PT-C AN are located in the control units: • Electromagnetic parking brake • Dynamic stability control 52 E70 Voltage Supply and Bus Systems 53 E70 Voltage Supply and Bus Systems