Table of Contents E70 Vertical Dynamics Systems Subject Page History of Vertical Dynamics .5 EDC .5 System Description .5 EHC .6 ARS.7 Adaptive Drive.8 What is "Adaptive Drive"? .8 General Information .8 System Overview .11 Active Roll Stabilization (ARS).11 ARS Bus Overview.11 ARS System Circuit Diagram.12 ARS Components .13 Vertical Dynamics Control (VDC) .14 VDC Bus Overview.14 VDC System Circuit Diagram.16 Legend forVDC System Circuit Diagram .17 VDC Components .18 Ride Height Sensor Location.19 Electronic Height Control (EHC).20 EHC System Diagram .20 EHC Pneumatic Diagram .21 EHC Components .22 System Functions.24 Active Roll Stabilization (ARS).24 Physical Conditions .24 Affect of the Self-steering Behavior .26 1. Identical stabilizing torque on both axles .26 2. Larger stabilizing torque on the front axle.26 System Dynamics.28 Comparison between the conventional stabilizer bar and the active stabilizer bar .28 Initial Print Date: 10/06 Revision Date: 11/06 Subject Page Operating States.29 Straight-ahead Travel.29 Cornering.29 Restricted Function .29 Hydraulic Circuit, Normal Function .30 Hydraulic Circuit, Fail-safe Function .31 Vertical Dynamics Control (VDC) .32 General Information .32 Objectives of the VDC System .34 System Network.35 Electronic Height Control (EHC).36 AirSpring Functions .36 Control Modes with Single-axle Air Suspension .36 Sleep-mode.36 Post-mode.37 Pre-mode.37 Normal mode .37 TiltS witch.38 Drive Mode .38 Kerb (Curb) .38 Curve .39 Lift.39 Special Modes (Belt).39 Functional Principle .40 Initialization/reset Behavior:.40 Control Sequence .40 Safety Concept.41 System Components.42 ARS Components.42 ARS Control Unit .42 ARS Control Unit Inputs.43 ARS Control Unit Outputs.43 Lateral Acceleration Sensor.44 Active anti-roll Bar .46 Function of Pressure Relief Valves .47 Operating Principle of Oscillating Motors .48 Front Axle Anti-roll Bar .49 Rear Axle Anti-roll Bar .50 Hydraulic Valve Block.51 Pressure Control Valves .52 Directional Valve .53 Failsafe Valve.53 Switch-position Recognition Sensor .53 Subject Page Front-axle/Rear-axle Pressure Sensors.53 Tandem Pump.54 Radial Piston Pump (part of the tandem pump).55 Vane-cell Pump (part of the tandem pump) .55 Fluid Reservoir .56 Fluid Level Sensor.57 Hydraulic-fluid Cooler .57 VDC Components.58 VDM Control Unit.58 Control Strategy .58 Display Control .59 Degradation Behavior in the Event of a Fault .60 Diagnostic Functions.60 EDC Satellite Control (with damper).61 EDC Satellite Control Unit .61 Twin-tube Gas Pressure Damper .62 Ride-height Sensor .63 EHC Components.66 EHC Control Unit .66 Air Supply Unit (LVA) .67 AirSuspension .68 Ride-height Sensor .68 Service Information.71 Steering Angle Calibration .71 ARS Initialization.71 ARS Bleeding Procedure .72 Diagnostics .73 Programming.76 Coding .76 Vertical Dynamics Systems Model: E70 Production: From Start of Production ■MICTIWIS After completion of this module you will be able to • Describe the differences between EDC and VDC • Locate and Identify VDC and ARS components 4 E70 Vertical Dynamics Systems History of Vertical Dynamics If we were to break down the common dynamic driving systems of today into the three coordinate axes by their principle of operation and assign them according to their function, BMW vehicles would have three different systems that would belong to the vertical dynamics systems. Vertical dynamics systems (effective direction mainly along the z-axis or vertical axis) • VDC/EDC - Vertical Dynamics Control (Electronic Damper Control) • EHC - Electronic Height Control • ARS - Active Roll Stabilization (or Dynamic Drive) EDC An EDC was firstfitted to a BMW in 1987, in the BMWE30M3. EDC I was firstfitted in series production in 1987 in the E32 (7 Series, 750i), which was based on the premise of manual toggling between a comfort and sports suspension setting. EDC II was then introduced in the E24 (6 Series). Even at this early stage of development, EDC functioned with characteristic curve mapping. Then in 1990, EDC III was fitted in the series production of the E31, E38 and E39. A modified form ofthis system, EDC-K, was also laterto be found in the E65. System Description Chassis designs should be able to offerthe driver (and occupants) the best possible standards in driving comfort, a very high level of driving safety, high agility and easy handling. Conventional, non-adjustable vibration dampers are only able to achieve a compromise between these objectives. The electronically controlled dampersystem was developed to practically eliminate this conflict of objectives. BMW EDC-K is a fully-automatic system that continually adjusts the damper settings to the current driving situation. 5 E70 Vertical Dynamics Systems The fundamental difference between EDC-K and EDC III is the design of the EDC valves and their control logic. EDC-K thus improves driving comfort without impairing driving safety. If the damper settings are too soft or comfortable, the vehicle will quickly begin to vibrate on unfavorable road conditions. EDC-K remains in the soft damper setting for as long as possible and only changes immediately to the harder setting when the road situation requires it. The system also guarantees consistently good vibration damping characteristics however the vehicle is laden. In addition, all vehicle movements which have an effect on vehicle handling are monitored constantly by sensors. All measurement results are analyzed by a microprocessor and appropriate control commands are transferred to the dampers. The damping force at the damper is adjusted by solenoid valves with infinite variability in line with the changing road surface conditions, load status and handling characteristics. EHC It all began for BMW with level control systems, which were available for the 7 Series (E23/E32), 6 Series (E24) and 5 Series (E28) as option or, in some vehicles, as part of the standard equipment. A distinction was made between: • Hydro-pneumatic suspension • Self-levelling suspension with electrohydraulic pump • Self-levelling suspension with engine driven piston pump • Single-axle air suspension • Twin-axle air suspension The purpose of a level control system is to maintain the height of the vehicle body as close as possible to a predefined level under all load conditions. Through a constant level of the body mainly the driving quality (e.g. camber, toe-in) will remain unaltered in the event of changes in payload. With the E39, the entire rear-axle load was supported by a single-axle air suspension for the first time. This system was controlled automatically under all operating states and thus did not permit any intervention by the driver. With the X5 (E53), the single-axle air suspension system was taken from the E39 and adapted accordingly. In addition, E53 customers were given the opportunity to order a twin-axle air suspension system fortheir vehicle. The twin-axle air suspension and its scope for adjustment by the driver has particular advantages by comparison with the single axle air suspension, especially as regards off road handling. Lowering the entire body makes it easierto get into and out of the vehicle and facilitates loading and unloading. 6 E70 Vertical Dynamics Systems ARS The customer-friendly name forthe option is "Dynamic Drive" and was first available in the 7 Series with the E65. The Dynamic Drive in the E60 is the same as the Dynamic Drive in the E65. As the vehicle drives through a bend, a rolling moment builds up about the vehicle's roll axis (x-axis) due to the centrifugal force that acts on the center of gravity of the vehicle. This momenttilts the vehicle body towards the wheel on the outside of the bend, causing the vehicle to rapidly approach its dynamic limits. The tilting of the body and the accom¬ panying shift in wheel load differences are counteracted by the use of anti-roll bars. • Conventional anti-roll bar - During cornering, the wheel suspension on the out¬ side of the bend is compressed and the wheel suspension on the inside ofthe bend rebounds. This has a twisting effect on the anti-roll bar (torsion). The forces arising in the bearing points ofthe anti-roll bar produce a moment that counteracts the tilt¬ ing ofthe body. The effect is to improve the distribution of loads acting on both wheels on the same axle. A disadvantage of a passive anti-roll bar is that the basic suspension tuning hardens when the suspension is compressed on one side ofthe vehicle during straight ahead travel.This results in a reduction in comfort. • Active anti-roll bar -The Dynamic Drive active chassis system also known as Active Roll Stabilization (ARS) - is a revolutionary step in chassis and suspension engineering. Forthe firsttime, the trade-off between handling/agility and comfort is largely eliminated. This results in a new type of "driving pleasure" typical of BMW. Dynamic Drive has two active anti-roll bars, which have a positive influence on body roll and handling characteristics. The fundamental feature of Dynamic Drive is the divided anti-roll bars on each axle. The two halves ofthe anti-roll bars are connected by a hydraulic oscillating motor. One half of the anti-roll bar is connected to the shaft ofthe oscillating motor, the otherto the housing ofthe oscillating motor.These active anti-roll bars control stabi¬ lizing moments: • which reduce the reciprocal movement ofthe vehicle body, • which make it possible to achieve high levels of agility and target precision over the entire road speed range, • and produce optimum self-steering characteristics. During straight-ahead travel, the system improves suspension comfort because the anti-roll bar halves are de-coupled, with the effect that the basic suspension tuning does not additionally harden when the suspension on one side is compressed. 7 E70 Vertical Dynamics Systems Adaptive Drive What is "Adaptive Drive"? With the Adaptive Drive option in the E70, Dynamic Drive active roll stabilization (ARS) and the variable damper adjustment (VDC) are functionally linked for the first time. The integration of both systems provides maximum safety, comfort and agility beyond compare for an SAV (Sports Activity Vehicle). Adaptive Drive reduces lateral roll of the body, which normally occurs during high-speed cornering or in the event of rapid swerving. Adaptive Drive also reduces the required steering angle and improves ride comfort coupled with an increase in driving dynamics. The customer can choose between a normal and a sporty basic setting. Adaptive Drive means increased driving pleasure and less tiring driving. Unpleasant pitching and lateral rolling of the body are diminished or eliminated entirely. The self-steering and load trans¬ fer characteristics of the vehicle are significantly improved. The reciprocal movements in the upper part of the body, which are inherent in the design of SAV vehicles, are considerably reduced. The vehicle can be driven with higher levels of precision and agility. The system also contributes to shorter braking distances. General Information Due to specific dynamic influences acting on the vehicle while it is in motion, the body is prone to self-movements, which can be divided into and illustrated by three categories. These degrees of freedom can be defined by basing the categories on the mathematics coordinate system with its three spatial coordinate axes. • Longitudinal dynamics - The main direction of motion - the direction of travel - is defined by the x- or longitudinal - axis. Longitudinal dynamic driving states, such as acceleration or braking, result in a pitching of the vehicle, which is where the vehicle is subjected to motion about the y axis. • Lateral dynamics - Lateral dynamics is where the direction of motion is along the y- or lateral - axis, e.g. as a result of steering or swerving, and the vehicle exhibits movement about the x-axis in the form of a rolling motion. • Vertical dynamics - Vertical dynamics is where the vehicle body moves along the z - or vertical - axis and the raising and lowering ofthe body, e.g. on bumpy roads, are described as vertical strokes. Movement ofthe vehicle about the z or vertical axis is known as yaw. Movements such as these occur during under or oversteering and are also commonly described as sporty drifting. 8 E70 Vertical Dynamics Systems Coordinate Axes Index Explanation Index Explanation 1 Yawing (about the vertical axis) 3 Rolling (about the longitudinal axis) 2 Pitching (aboutthe vertical axis) These basic dynamic driving properties depend, in particular, on the following vehicle dimensions. 9 E70 Vertical Dynamics Systems The position of the center of gravity in a vehicle, its distance from road level, the wheelbase and the track width are decisive parameters in the dynamic driving behavior of a vehicle. z Index Explanation Index Explanation 1 Distance forthe center of gravity from the road surface 3 Wheelbase 2 Track width 10 E70 Vertical Dynamics Systems System Overview Active Roll Stabilization (ARS) ARS Bus Overview JB Kombi DSC SiN SZL DSC OME ODE CAS FRM Index Explanation Index Explanation KOMBI Instrument cluster SZL Steering Column Switch Cluster CAS Car Access System DSC Dynamic Stability Control FRM Footwell Module ARS Active Roll Stabilization J B J unction box DME Digital Motor Electronics DSC_SEN DSC Sensor VDM Vertical Dynamics Management 11 E70 Vertical Dynamics Systems ARS System Circuit Diagram Index Explanation Index Explanation 1 Hydraulic valve block 8 Car Access System 2 Dynamic Stability Control 9 Footwell Module 3 J unction Box (control unit) 10 Steering Wheel Switch Cluster 4 Active Roll Stabilization 11 Kombi 5 Lateral acceleration sensor 12 Hydraulic fluid sensor 6 Vertical Dynamics Management 13 Digital Motor Electronics 7 DSC Sensor 12 E70 Vertical Dynamics Systems ARS Components Index Explanation Index Explanation 1 Hydraulic-fluid reservoir 6 Valve block 2 Hydraulic-fluid radiator (cooler) 7 Lateral acceleration sensor 3 Front oscillating motor 8 Hydraulic lines 4 Tandem pump 9 Rear oscillating motor 5 Control unit 13 E70 Vertical Dynamics Systems Vertical Dynamics Control (VDC) VDC Bus Overview JB KL Afl3 -' - OME DDE GWS Index Explanation Index Explanation J B J unction box VDM Vertical Dynamics Management DSC_SENS DSC Sensor EDC SVL Electronic Damper Control satellite, front left SZL Steering Column Switch Cluster EDC SVR Electronic Damper Control satellite, front right ARS Active Roll Stabilization EDC SHL Electronic Damper Control satellite, rear left DME Digital Motor Electronics EDC SHR Electronic Damper Control satellite, front right GWS Gear Selector Switch 14 E70 Vertical Dynamics Systems 15 E70 Vertical Dynamics Systems VDC System Circuit Diagram (9 0 16 E70 Vertical Dynamics Systems Legend forVDC System C ircuit Diagram Index Explanation Index Explanation n Electronic Damper Control satellite, front left 9 Electronic DamperControl satellite, rear left 2 Ride height sensor, front left 10 Ride height sensor, rear left 3 Digital Motor Electronics 11 Steering Column Switch Cluster D Ride height sensor, front right 12 Gear Selector Switch 5 Electronic DamperControl satellite, front right 13 J unction box 6 Ride height sensor, rear right 14 Active Roll Stabilization 7 Electronic DamperControl satellite, rear right 15 DSC Sensor 8 Vertical Dynamics Management 17 E70 Vertical Dynamics Systems VDC Components Index Explanation Index Explanation 1 Electronic Damper Control satellite, front right 4 Vertical Dynamics Management 2 Gear Selector Switch 5 Electronic Damper Control satellite, rear left 3 Electronic Damper Control satellite, rear right 6 Electronic Damper Control satellite, front left 18 E70 Vertical Dynamics Systems Ride HeightSensorLocation Index Explanation 1 Ride height sensor (4x) 19 E70 Vertical Dynamics Systems Electronic Height Control (EHC) EHC System Diagram 3 a_ HI H H 20 E70 Vertical Dynamics Systems Legend for EHC System Diagram Index Explanation Index Explanation 1 Footwell module 4 Right height sensor, right 2 Airsupply unit 5 Ride height sensor, left 3 EHC control unit 6 Headlight range adjustment sensor EHC Pneumatic Diagram Index Explanation Index Explanation A LVA, Airsupply unit 7 Solenoid valve, left side B Compressor unit 8 Restrictor C Solenoid valve block 9 Restrictor 1 Air intake 10 Air drier 2 Pressure limiting/holding valve 11 Non-return valve 3 Outlet valve 12 Electric motor 4 Solenoid valve, right side 13 Compressor 5 Air spring, rear right 14 Air cleaner 6 Air spring, rear left 21 E70 Vertical Dynamics Systems EHC Components z) l) ZJ v! Index Explanation Index Explanation 1 Air cleaner 6 Ride height sensor, right 2 Retaining plate 7 EHC control unit 3 LVA, Air supply unit 8 Air spring, rear left 4 Pneumatic lines 9 Ride height sensor, left 5 Air spring, rear right 22 E70 Vertical Dynamics Systems 23 E70 Vertical Dynamics Systems System Functions Active Roll Stabilization (ARS) Physical Conditions When the vehicle drives through a bend, the vehicle is subjected to lateral acceleration [ay], which acts on the vehicle's center of gravity [1], The vehicle body rolls about the roll axis [2] due to the kinematics of the front and rear axle. The roll angle is formed, (max. 5°). This produces a maximum change in level on the wheel arch of 10 cm. Index Explanation Index Explanation A Vehicle without Adaptive Drive Ma Body torque B Vehicle with Adaptive Drive 1 Center of gravity [SP] M Rolling moment 2 Roll axis [RA] ay Lateral acceleration Fy Lateral force 9 Roll angle h Lever arm center of gravity height In a passive vehicle with conventional suspension, the rolling moment [M ] is absorbed by the anti-roll bars and springs. The springs on the outside of the bend are com¬ pressed and the springs on the inside of the bend rebound. In addition, the anti-roll bars rotate. A roll angle [.] forms between the vertical and the body. In a vehicle with Adaptive Drive, the rolling moment [M ] can be fully compensated for by the active anti-roll bars up to a specific rate of lateral acceleration ay. A roll angle only begins to form once the rolling moment [M ] has exceeded the moment [M a] actively set by the anti-roll bar. The residual rolling moment [M] is then absorbed by the passive springs. 24 E70 Vertical Dynamics Systems The active body moments [M a] at the front and rear axle counteract the rolling moment [M ]. Using this approach, the roll angle is compensated for in accordance with the characteristic curve specified in the control unit. The roll angle is fully compensated for up to a lateral acceleration of approximately 5 m/s 2 (0.5 g). A roll angle can form even with Adaptive Drive, but only at higher rates of lateral accelera¬ tion. The roll angle together with an increasing understeering trend therefore provide the driver with an indication that the vehicle is approaching its limit range. There is no compensation fortire compression caused by the rolling moment [M ]. The roll angle shown is achieved when the vehicle is unladen and the driver is in the vehicle. When the vehicle is fully laden, the larger body mass effects a greater lateral force on the vehicle. Depending on the arrangement of the vehicle load (inside the vehicle or on the roof), there may also be a change in leverage [h]. The vehicle will then exhibit a somewhat larger roll angle than is shown in the control characteristic curve. A fully laden passive vehicle still forms a larger roll angle. The distribution of the active body torque between the front and rear axle depends on the road speed. 25 E70 Vertical Dynamics Systems Affect of the Self-steering Behavior The self-steering behavior can be decisively influenced by the distribution of the stabiliz¬ ing torque on the axles. The greaterthe stabilizing torque on an axle, the lowerthe lateral forces transmitted on this axle. Two cases are described below with different distributions of stabilizing moments at the axles: 1. Identical stabilizing torque on both axles Handling is NEUTRAL. The front wheels can apply about the same amount of lateral force on the road as the rear wheels without drive torque. The handling conditions are neutral. A vehicle which is tuned to neutral handling conditions provides very agile handling, the steering reacts very quickly. The driver experiences precise handling. Even an inexperienced driver can control a vehicle which is tuned to neutral handling very well at low speeds. 2. Larger stabilizing torque on the front axle Handling is UNDERSTEERING. The front axle wheels cannot apply the same amount of lateral force on the road as the rear axle wheels. The vehicle suffers understeer. A greater steering-wheel angle is required to be able to follow the desired course. An understeering vehicle can generally be well controlled even by an inexperienced driver at higherspeeds and higher cornering speeds. This very sensitive handling reduces the vehicle's agility. Adaptive Drive adjusts the stabilizing moments at the front and rear axles in such a way that different handling characteristics are produced for low and high speeds. y Index Explanation Index Road Speed Explanation 1 Front axle A Low Neutral 2 Rear axle B High Understeering 26 E70 Vertical Dynamics Systems More active body moment [Ma] is required with increasing lateral acceleration. The characteristic curves are shown fortwo different road speeds. The following illustration shows the relationship between lateral acceleration [ay] and steering wheel angle [LW] for the passive vehicle and for the vehicle with Adaptive Drive and in different road speed ranges. y) Index Explanation Index Explanation 1 v = 15 km/h 2 v = 250 km/h Index Explanation Index Explanation 1 Passive, agility v < 100 km/h 1 Passive, agility v > 150 km/h 2 RS, agility v < 100 km/h 2 ARS, agility v > 150 km/h 27 E70 Vertical Dynamics Systems The passive vehicle is configured as slightly understeering irrespective of the speed range. Adaptive Drive is tuned to be neutral in the lower road speed range. The driver does not have to steer as much to drive through the same bend. This results in optimum handling and agility. In the upper speed range, both vehicles behave almost identically with regard to the required steering angle on the same bend. The hydro-mechanical concept is designed so that a greater active stabilizing torque cannot occur on the rear axle than on the front axle under any circumstances. This means that mechanically and hydraulically the vehicle with Adaptive Drive is safeguarded such that no oversteering and therefore for normal customers no critical handling characteris¬ tics can occur under any circumstances. System Dynamics Adaptive Drive has to respond as fast as is required in the event of rapid lane changes, rapid cornering or rapid changes of direction on winding country roads. The system dynamics of Adaptive Drive are determined by the duration of the following stages: Process Time Signal detection by sensor, processing of sensor signals in the control unit, valve control Approximately 10 milliseconds Change of direction, reversal of moment direction, directional valve Approximately 30 milliseconds Pressure increase (force per wheel) 0 - >30 bar(0 - >350 N) 0 - >160 bar(0- >2100 N) Approximately 120 milliseconds Approximately 400 milliseconds Comparison between the conventional stabilizerbarand the active stabilizer bar Active stabilizer bars introduce fewer comfort reducing forces into the body than passive stabilizer bars. In this case a differentiation must be made depending on the frequency with which the forces were introduced. Road stimulus Anti-roll bar behavior At approximately 1 Hz (natural body frequency) With smaller strokes, the active anti-roll bartwists more easily than a conventional anti-roll bar The forces introduced into the body are reduced, the vehicle becomes more comfortable and body displacement is reduced From 8 Hz (wheel natural frequency) Both anti-roll bars behave in a similar way. On a vehi¬ cle with an active stabilizer bar this is because the fluid is not displaced so quickly. 28 E70 Vertical Dynamics Systems Operating States Straight-ahead Travel When the engine is started, the pump delivers hydraulic fluid to the system and a back pressure builds up. The pressure difference of approximately 1 bar which exists between the chambers of the control motor is very small and has no effect on the anti-roll bar. The pressure valves forthe front-axle anti-roll bar(PVV) and rear-axle anti-roll bar(PVH) are not supplied with current and are therefore open. The hydraulic fluid can flow back into the hydraulic-fluid reservoir directly. This condition remains unchanged as long as the vehicle is travelling straight ahead. The system function is displayed continuously up to 15 km/h. The full stabilization poten¬ tial is available from 15 km/h onwards. Cornering As the vehicle enters a bend, the signals from the lateral acceleration sensor are sent to the ARS control unit. The control unit now sends a pulse-width-modulated signal (PWM) to the pressure valves forthe front and rear-axle anti-roll bars. The strongerthe lateral acceleration, the greaterthe signal will be (current). The strongerthe current supplied to the valve, the more the valve closes and the higherthe pressure which builds up in the anti-roll bars. The pressures at the anti-roll bars are detected by pressure sensors [10, 11] and sent to the control unit. Direction valve [9] is controlled by the control unit to increase and maintain pressure suit¬ able to the characteristic of the bend (left or right hand bend). A sensor [8] detects the switch position of the direction valve. Restricted Function If a fault is detected, the system enters failsafe mode. The control unit stores the fault in the fault memory and displays the failsafe condition in the instrument cluster. Failsafe condition is retained until start-up is completed without a fault. Failsafe valve [7] is closed by a spring in the event of a system malfunction. The hydraulic fluid in the front anti-roll bar is sealed in, thereby ensuring sufficient stabilization and an understeering effect equivalent to that of a conventional chassis. External leakage: External leakage is detected by the front and rear pressure sensors and results in the total failure of the system. The failsafe situation is shown in the following hydraulic circuit diagram overview. 29 E70 Vertical Dynamics Systems Hydraulic Circuit, Normal Function 10 11 14 <15 Index Explanation Index Explanation 1 Front oscillating motor [S MV] 9 Direction valve [RV] 2 Rear oscillating motor [SM FI] 10 Rear-axle pressure sensor [DSH] 3 Front-axle hydraulic circuit 1[V1] 11 Front-axle pressure sensor [DSV] 4 Front-axle hydraulic circuit 2 [V2] 12 Front-axle pressure valve [PVV] 5 Rear-axle hydraulic circuit 1 [HI] 13 Rear-axle pressure valve [PVH] 6 Rear-axle hydraulic circuit 2 [H2] 14 Tandem pump [P] 7 Failsafe valve [FS] 15 Hydraulic-fluid reservoir[HB] 8 Switch-position recognition sensor [SSE] 30 E70 Vertical Dynamics Systems Hydraulic Circuit, Fail-safe Function 14 , (15 Index Explanation Index Explanation 1 Front oscillating motor [S MV] 9 Direction valve [RV] 2 Rear oscillating motor [SM FI] 10 Rear-axle pressure sensor [DSH] 3 Front-axle hydraulic circuit 1[V1] 11 Front-axle pressure sensor [DSV] 4 Front-axle hydraulic circuit 2 [V2] 12 Front-axle pressure valve [PVV] 5 Rear-axle hydraulic circuit 1 [HI] 13 Rear-axle pressure valve [PVH] 6 Rear-axle hydraulic circuit 2 [H2] 14 Tandem pump [P] 7 Failsafe valve [FS] 15 Hydraulic-fluid reservoir[HB] 8 Switch-position recognition sensor [SSE] 31 E70 Vertical Dynamics Systems Vertical Dynamics Control (VDC) General Information The Vertical Dynamics Control (VDC) system being introduced forthe time from SOP with the E70 is a component of the Adaptive Drive equipment package and is an advancement of the EDC-K already fitted on the E65. Like EDC-K, VDC is notable for its continually adjustable dampers whereby, within certain limits, as many damping charac¬ teristic curves (damping force - piston speed) as desired can be plotted. The characteris¬ tic curve used depends on the driving situation, in other words, the variables that describe the dynamic driving state of the vehicle and which are selected automatically at the driver's command. Comparison between EDC-K in the E65 and VDC in the E70: EDC-K VDC Model E65 from introduction into series production from 7/2001 E70 from SOP 10/06 in the Adaptive Drive equipment package Program Selection via Control Display and controller "SPORT" button next to gear selector switch Control unit EDC-K control unit on the device hold¬ er behind glove compartment VDM control unit: rear left of luggage compartment FourEDC satellite control units directly on the damper Sensors Vertical: vertical acceleration sensor, front left, front right, rear right Longitudinal: wheel speed sensors, front left, front right Lateral: steering angle sensor (LWS) from the steering column switch cluster Vertical: fourvertical acceleration sensors integrated in the EDC satellite-control units, four ride-height sensors connected directly to the VDM control unit Longitudinal: wheel speed sensors orvehicle speed from the DSC control unit Lateral: steering angle sensor (LWS) from the steering column switch cluster, Rotor position sensor (if Active Steering fitted), lateral acceleration (DSC sensor) as redundant signal to the steering angle Damper Twin-tube gas-pressure dampers Twin-tube gas-pressure dampers Diagnostics fully compatible VDM and EDC satellite control units flash-programmable Programming EDC-K control unit is flash programmable VDM and EDC satellite control units are flash programmable Coding VDM and EDC satellite control units are codable Malfunction display Messages in the Control Display or instrument cluster Messages in the Control Display or instrument cluster Testing Diagnostic tester Diagnostic tester 32 E70 Vertical Dynamics Systems 33 E70 Vertical Dynamics Systems Objectives oftheVDC System The primary objective oftheVDC system to improve ride comfort while maintaining driving safety at an invariably high level. H igh levels of ride comfort are achieved when the vehicle body hardly moves along the vertical axis in spite of excitations of the vehicle induced by cornering or by the road surface itself (bumps, gaps). Forthis reason, the adjustable dampers are operated in line with a soft, comfortable damping characteristic curve in as many situations as possible. High levels of driving safety are achieved if the wheels never lose contact with the road surface and a high support force is available if required. A harder damping characteristic is therefore set if the driving situation or driver's intervention (e.g. steering, braking) demands it. As with EDC-K,the dampers have an infinite number of damping characteristic curves at their disposal; unlike EDC-K, however, the dampers are controlled not only axle by axle but also at each individual wheel. Index Explanation Index Explanation A Rebound stage 1 Comfort B Compression stage 2 Stability X Piston speed (m/s) 3 S afety y Damping force (N) 34 E70 Vertical Dynamics Systems In its regulation, the system uses the complete characteristic map of the rebound and compression stages between the comfort (1) and stability (2) threshold curves. In the event of a fault, the control range is minimized to safety characteristic curve (3). System Network The VDC system is a mechatronic system consisting of electronic, hydraulic and mechanical subsystems. These can be subdivided by function as follows: • Detection of input signals - Sensors for ride heights and rates of vertical acceleration to permit detection of the driving state and the prevailing road conditions - Control element to enable the driverto set the damping program (comfort, sport). This is located on, and electrically integrated in, the gear selector switch. - Steering angle (output by the SZL control unit via F-CAN) for preemptive detection of cornering - Lateral acceleration (out by the DSC sensorvia F-CAN) for detection of cornering - Vehicle speed orwheel speeds (output by the DSC control unit via F-CAN) • Processing unit - VDM control unit - This checks the plausibility of the incoming signals and uses control algorithms that deliver damping forces at individual wheels as a set point value - EDC satellite control units - These process the signals from the vertical acceleration sensors on the one hand and output the processed signal. On the other hand, they convert into a valve current the target force from the VDM control unit by means of a stored characteristic curve • Actuators The electrically controllable valve in the adjusting damper makes it possible to realize the different damping force characteristic curves • Communications media The VDM control unit is connected to the PT-CAN, F-CAN and FlexRay; the EDC satellite control units are only connected to the FlexRay 35 E70 Vertical Dynamics Systems Electronic Height Control (EHC) Air Spring Functions The various control modes in the E70 are designed in a similar way to those in the E6x: Control Modes with Single-axle Air Suspension Ongoing control operations are not affected by transitions from one mode to another. Afterthe procedure of the follow-up time the EHC control unit sets the sleep mode. Any yet active control operations will be terminated. Sleep-mode The vehicle is in Sleep-mode at the latest when it has been parked forlongerthan 16 minutes without a door or hood/trunk lid being operated orthe terminal status changing. This is the initial state of the control system. No control operation is performed in Sleep mode. The control system goes into Pre-mode when a wake-up signal is received by the EHC control unit. 36 E70 Vertical Dynamics Systems Post-mode Post-mode is activated in orderto compensate for any inclination orto adjust the ride height after driving and between the Pre mode and Sleep mode. The Post-mode is limited in time to 1 minute. This mode is only executed if the engine has been running before the system switches into this mode. If the engine has not been running, Sleep mode is entered directly from Premode. The control operation is performed in a narrow tolerance band of-6 mm and is terminat¬ ed at-4 mm. The quick signal filter is used. In the event of an inclination (Kerb mode), the control operation takes place forthe nominal heights applicable in this situation. Pre-mode The activation of the Pre-mode with follow-up triggering afterwards takes place with flap change orchange ofterminal R from ON to OFF. The ride height ofthe vehicle is moni¬ tored and evaluated with a wide tolerance band. In Pre-mode, the vehicle is only controlled up to the nominal height if the level is signifi¬ cantly below the nominal height. The control tolerance band is -60 mm from the mean value. This control tolerance ensures that the vehicle is only controlled up in the case of large loads in orderto increase the ground clearance priorto departure. Small loads give rise to small compression travel and this is compensated only when the engine is started. This control setting helps to reduce the battery load. With single-axle air suspension, the vehicle is controlled down when the mean value of both ride height signals is > 0 mm and one side is in excess of +10 mm. In this mode, only the mean value ofthe two ride height signals (fast filter) is considered when deciding whetherthere is a need fora control operation.There is no inclination detection in Pre-mode. Normal mode Normal mode is the starting pointforthe vehicle's normal operating state. It is obtained by way ofthe "Engine running" signal. Ride level compensation and a change in the vehicle's ride height are possible. The compressor starts up as required. A narrower tolerance band than that in Pre mode can be used because the battery capacity does not have to be protected. The fast filter is used with a narrow tolerance band of ± 10 mm. In this way, ride level compensation takes place outside a narrow tolerance band of ±10 mm. The faster filter allows the system to respond immediately to changes in ride level. Evaluation and control are performed separately for each wheel. When a speed signal is detected, the EHC control unit switches into Drive mode. When the vehicle is stopped, the EHC control unit switches into Normal mode. The system switches back into Normal mode only when a doororthe trunk lid is also opened. If none ofthe doors orthe boot lid is opened, the vehicle logically cannot be loaded or unloaded. 37 E70 Vertical Dynamics Systems This prevents a control operation happening when the vehicle is, for example, stopped at traffic lights and the ride height is above the mean value due to a possible pitching motion at the rear axle. TiltS witch The single-axle air suspension enters this mode if a signal is registered on the vehicle bus bytheTMPS. A flat tire can be relieved of load thanks to the "Inclination in run flat mode" function. When this message is received, the flat tire can be relieved of load by the venting of air on the defective side and an intake of air on the unaffected side of the vehicle. Drive Mode Drive mode forthe single-axle air suspension is activated when a speed of >1 km/h is detected. Low-pass filters are used. In this way, only changes in ride height over a prolonged period oftime (1000 seconds) are corrected. These are merely the changes in ride height, caused by vehicle compression and a reduction in vehicle mass due to fuel consumption. The high-pass filter (fast filter) is used during the control operation. The slow filters are re-initialized atthe end of the control operation. The markedly dynamic height signals caused by uneven road surfaces are filtered out. Kerb (Curb) The Kerb mode prevents the inclination caused by the vehicle mounting an obstacle with only one wheel from being compensated. Compensation would cause a renewed inclination ofthe vehicle and result in a renewed control operation afterthe wheel came off the obstacle. Kerb mode is activated if the difference in height between the left and right-hand side of the vehicle is >28 mm and this difference remains forlongerthan 0.9 s. No speed signal may be present for this mode to be set. The system switches from single-wheel control to axle control. Kerb mode is quit if the difference between the left and right-hand side ofthe vehicle is <24 mm and this difference remains forlongerthan 0.9 s or if the speed is > 1 km/h. If the system switches from Kerb mode to Sleep mode, this status is stored in the EEPROM. If the vehicle is being loaded or unloaded in Kerb mode, the EHC control unit calculates the mean value forthe axle from the changes in ride height determined from the spring travel on the right and left-hand side. A change in ride level is initiated if the mean value of compression or rebound atthe axle is outside the tolerance band of ± 10 mm. The left and right sides ofthe vehicle are raised or lowered in parallel. The height difference between the two sides is maintained. 38 E70 Vertical Dynamics Systems Curve Since rolling motions have a direct impact on the measured ride levels, an unwanted control operation would be initiated during longer instances of cornering with an appropriate roll angle in spite of the slow filtering of the Drive mode. The control operations during cornering would cause displacement of the air volume from the outer side to the inner side of the curve. Once the curve is completed, this would produce an inclination which would result in a further control operation. Curve mode prevents this adjustment by stopping the slow filtering when cornering is detected and cancelling any adjustment that may have been started. Curve mode is activated above a lateral acceleration of >2 m/s 2 and deactivated at <1.5 m/s 2 . The lateral acceleration is recorded by the DSC sensor. Lift The Lift mode is used to prevent control operations when a wheel is changed or during work on the vehicle while it is on a lifting platform. This mode is detected when the permitted rebound travel at one or more wheels is exceeded >65 mm. A jacking situation is also detected and the ride height stored if the lowering speed drops below the value of 0,7 mm/s for 8 seconds. If the vehicle is raised only slightly and the permitted rebound travel has not yet been reached, the control operation attempts to readjust the ride height. If the vehicle is not lowered, a carjack situation is recognized after a specific period of time and this ride height is stored. A reset is performed if the vehicle is again 10 mm below this stored ride height. Special Modes (Belt) Belt mode is set during assembly in the works to prevent control operations. When Belt mode is activated, no message will be displayed in the instrument cluster. This is only recognizable by the non-deletable fault memory entry "energy-save mode active". Belt mode is cleared by means of diagnostics control only. The Belt mode can no longer set afterwards. New EHC control units (spare part) are supplied with Belt mode set. Control operations are not performed, the safety concept only operates with limited effect. 39 E70 Vertical Dynamics Systems Control modes Single-axle airsuspension Sleep No control, load cutout on Post Approximately. 1 minute fast filter 2 s, very narrow tolerance band < -6 / > 6 mm, control ends at <-4 />4 mm Pre Approximately. 20 minutes fast filter 2 s, wide tolerance band controlled up when <-60 mm, controlled down when mean value > 0 mm and one side > 10 mm Tilt_S witch Can be activated and deactivated by coding; not activated when a trailer is connected to the vehicle. Activated in response to RDC/RPA bus message Normal Engine running: Fast filter 2 s, narrow tolerance band ± 10 mm Drive v > 1 km/h, slow filter 1,000 s, narrow tolerance band ± 10 mm Kerb ON when: difference between left and right-hand sides of vehicle > 28 mm, longerthan 0.9 s changeover from single-wheel control to axle control OFF when: difference between left and right-hand sides of vehicle < 24mm, t = 0.9 s orv>l km/h Curve ON when: lateral acceleration >2 m/s2 OFF when: lateral acceleration <1.5 m/s2 Lift ON when: rebound travel >65 mm at one or more wheels J ack on at: Lowering speed drops below the value 0,7 mm/s for 8 s, ride height storing OFF when: level change <-10 mm, ride height drops below stored setting by > 10 mm Functional Principle Initialization/reset Behavior: Different checks and initializations are carried out when the EHC control unit is powered up after a reset (triggered by an undervoltage). The system is only enabled after the tests have been successfully completed and starts to execute the control programs on a cyclical basis. Occurring faults are stored and displayed. Control Sequence In an ongoing control operation, the high-pass filter (fast filter) is always used to prevent the controlled height from overshooting the nominal value. If a low-pass filter (slow filter) were used to calculate the ride height, brief changes of ride height would be "absorbed". The low-pass filter is used when the vehicle is in motion (see Normal mode) to filter out vibrations induced by prevailing road conditions on this basis of this method offiltering. The high-pass filter is used to respond quickly to ride level deviations from set point. These take place while the vehicle is stationary in the event of large load changes (see Pre-mode). Both sides of the vehicle are controlled individually, i.e. even the set point/actual-value comparison for both sides is carried out individually. Exception: check for falling below the minimum height in Pre-mode and Kerb mode.The left/right mean values are taken into consideration here. 40 E70 Vertical Dynamics Systems The following stipulations are applicable here: • Raising before lowering • All valves controlled with control in the same direction • Individual wheel deactivation. To ensure reliable closing of the non-return valve in the air drier, the drain valve is controlled by the EHC control unit briefly for 200 ms afterthe control-up procedure has ended. The permissible ON period ofthe components is monitored while control up operations are executed. Safety Concept The safety concept is intended to inhibit any system malfunction, particularly unintention¬ al control operations, through the monitoring of signals and function-relevant parameters. If faults are detected, the system is switched over or shut down depending on the components concerned. The driver is informed of a malfunction by the display, and detected faults are stored for diagnostics purposes. In orderto ensure high system availability, existing faults, as far as possible, are cleared with terminal 15 ON. This is done by resetting the fault counterto zero. However, the fault memory content in the EEPROM is retained and can be read out for diagnostic purposes. The system is then operational again. The fast troubleshooting helps to detect existing faults before control operations can take place. Only lowering is permitted if: • The permissible supply voltage of 9 volts is undershot • The permissible compressor running time of 480 seconds is exceeded A reset takes place if the voltage is in the OK range of 9 to 16 volts or after the compres¬ sor pause time of 100 seconds has elapsed. Only raising is permitted if: • The permissible control down period of 40 seconds is exceeded • The reset takes place the next time the vehicle is driven or afterthe next control-up procedure. No control if: • The permissible supply voltage of 16 volts is exceeded The reset takes place as soon as the voltage is in the OK range. 41 E70 Vertical Dynamics Systems System Components ARS Components ARS Control Unit The ARS control unit is located in the vehicle interior nearthe right-hand A-pillar. Index Explanation 1 ARS Control unit The ARS control unit is supplied with powervia terminal 30 and is protected by a 10 A fuse. The ARS control unit is activated exclusively by the Car Access System (CAS) on a CAN wake-up line after "ignition ON". A vehicle authentication process takes place when the system is started. This compares the vehicle identification numberfrom CAS with the vehicle identification number which is encoded in the ARS control unit. Then the ARS control unit's hardware and software are checked. All the outputs (valve magnets) are subjected to a complex check for short circuits and breaks. If there is a fault, the system switches the actuators into a safe driving condition. The ARS control unit switches off if there is undervoltage or overvoltage. The ARS control unit learns the offsetforthe steering angle and the lateral acceleration during start-up and during driving. 42 E70 Vertical Dynamics Systems ARS Control Unit Inputs The ARS control unit uses the input signals to calculate control of the actuators. The input signals are also checked for plausibility and used for system monitoring. The ARS control unit receives the following input signals: • Lateral acceleration • PT-CAN • Front-axle circuit pressure • Rear-axle circuit pressure • Switch-position detection position • Fluid level sensor signal. The most important Dynamic Drive control signal is the measured lateral acceleration value. Additional information from the PT-CAN that describes lateral dynamics includes the road speed signal, steering wheel angle and the yaw velocity from the yaw rate sensor. From this information, the stabilization requirement is determined and the appropriate active moments are implemented. The road speed and steering angle signals also help to improve the response time of the system. ARS Control Unit Outputs All outputs are compatible with diagnostics and protected against short-circuit. The outputs include controls for: • Pressure regulating valves forfront and rear axle • Directional valve • Failsafe valve • 5 V powersupplyforthe sensors: - Lateral acceleration sensor - Pressure sensors at the front and rear axle - Switch-position recognition sensor (SSE). The valves are controlled by the supply of current regulated by pulse-width modulation (PWM). The current measurements of the individual coil currents are designed with redundancy. The valve currents are mutually checked for plausibility on a continuous basis. Thanks to the current measurement, the pressure can be set more precisely and the switch valves can be monitored electronically. 43 E70 Vertical Dynamics Systems A telegram is sent to the DM E on the PT-CAN. The telegram contains information on how much powerthe tandem pump currently requires to supply the active anti-roll bars. In this way, output at the engine can be increased to satisfy the additional power requirement. A regular data signal (alive signal) is output and read by other ARS control units to identify whether the system is still active. All signal faults are detected and stored in the non-volatile memory. Fault symptoms of output signals are • Short circuit to terminal 30 and terminal 31 • Open circuit and • Valve short circuits. Lateral Acceleration Sensor The lateral acceleration sensor supplies the main sensor signal. It measures the lateral acceleration of the vehicle during cornering up to a measurement range of 1.1 g. It is installed on the base plate underthe right front seat. The ARS control unit can learn an offset during start-up and when the vehicle is in motion. 44 E70 Vertical Dynamics Systems 45 E70 Vertical Dynamics Systems Active anti-roll Bar The oscillating motor and the oscillating motor housing are joined by one half of the anti¬ roll bar. The active anti-roll bar consists of the oscillating motor and the anti-roll bar halves fitted to the oscillating motor, with press-fitted roller bearings fortheir connection to the axle carriers. The use of roller bearings ensures optimum comfort thanks to better response and reduced control forces. Index Explanation Index Explanation 1 Oscillating motor housing 2 Oscillating motor shaft The oscillating motor of the front axle stabilizer bar is fitted with 2 pressure relief valves. Airfilter elements are fitted to the pressure relief valves. These airfiltercaps with Goretex inserts must not be removed. There are screw plugs in the area of the pressure relief valves on the oscillating motorof the rear-axle anti-roll bar. 46 E70 Vertical Dynamics Systems Index Explanation Index Explanation 1 Pressure relief valve with airfiltercap 4 Hydraulic connection 2 Pressure relief valve with airfiltercap 5 Hydraulic connection 3 Front oscillating motor Function of Pressure Relief Valves When the vehicle is driven on poor road surfaces, brief underpressures (cavitation) result from the movements of the anti-roll bar, which in turn could cause rattling noises. Pressure relief valves have been fitted on the front oscillating motor in orderto eliminate these noises. These pressure relief valves allow the filtered airto flow into the oscillating motor. This prevents cavitation. This small quantity of air is absorbed by the hydraulic fluid (Pentosin) to form an emulsion, which is discharged during subsequent activations of the oscillating motor. The surplus air is separated in the expansion tank. Since no noises can be heard at the rear axle, the pressure relief valves have been omitted from the rear oscillating motor. 47 E70 Vertical Dynamics Systems Operating Principle of Oscillating Motors The oscillating motor has three functions to perform: • The oscillating motor transfers the torque into the anti-roll bars. • The oscillating motor de-couples the anti-roll bar halves. • In the event of system failure (failsafe mode), the front axle anti-roll bar creates sufficient damping via the oscillating motor hydraulic fluid (hydraulic locking). It now works like a conventional anti-roll bar. Exception: If the oscillating motor chambers no longer contain any fluid as a result of a leak, the front axle anti-roll bar can no longer create damping. The opposing chambers in the oscillating motor are connected to one another. The same pressure exists in both chambers. Two chambers are supplied with high pressure fluid using one connection. The two other chambers are connected to the tank via the return line. The forces FH (High) orFL (Low) are created as a result of the differences in pressure. Since FH is greaterthan FL, a torque MS is produced, which causes the shaft to turn in relation to the housing. Since one half of the stabilizer bar is connected to the shaft, and the other with the hous ing, the two halves turn in opposite directions. This torque MS generates the active moment M A around the vehicle longitudinal axis via the anti-roll bar connections which counteracts the rolling moment M during cornering. The shell is forced upwards on the outside of a curve, and dragged down on the inside of a curve. 48 E70 Vertical Dynamics Systems The maximum body torque on the front and rear axle occurs when there is a high degree of lateral acceleration. The system pressure is then 160 bar at the front axle and also 160 bar at the rear axle. At 160 bar, both oscillating motors generate a force of 850 Nm. If the oscillating motortwists as a consequence of external forces (road excitation, e.g. bumps or potholes), the oscillating motorthen acts as a torsional vibration damper. As a result of the twisting action, fluid is forced out of the two chambers. The fluid that is forced outflows through the lines and the hydraulic valve block, the hydraulic resistances in which produce a damping effect. In the event of failsafe locking (hydraulic locking), the oscillating motor can only twist with a very high damping effect as a consequence of the hydraulic jamming in the oscillating motor. Front Axle Anti-roll Bar vi> -d) e) v i> i 5 Index Explanation Index Explanation 1 Anti-roll bar link connection to swivel bearing 4 Oscillating motor 2 Anti-roll bar bracket 5 Anti-roll bar links 3 Anti-roll bar The anti-roll bar is mounted on the front-axle carrier. The anti-roll bar links are connected to the "goose-necks" of the swivel bearings. 49 E70 Vertical Dynamics Systems Rear Axle Anti-roll Bar The anti-roll bar is mounted behind the rear axle carrier. The anti-roll bar links are connected to the rear-axle swinging arms. & Q) Q) & Index Explanation Index Explanation 1 Lines from the hydraulic valve block 3 Anti-roll bar 2 Anti-roll bar links 4 Oscillating motor 50 E70 Vertical Dynamics Systems Hydraulic Valve Block The hydraulic valve block is located on the floor plate of the vehicle behind the front right hand wheel housing level with the front right hand door. The hydraulic valve block is connected to a carrier plate bolted to the body. The hydraulic valve block houses the following valves and sensors: • 2 pressure regulating valves; one for the front axle and one for the rear axle • one direction valve • one failsafe valve • 2 pressure sensors; one sensorforthe front axle, one sensorforthe rear axle • one switch-position recognition sensor. The hydraulic valve block has the following connections: • 2 lines to the oscillating motor at the front • 2 lines to the oscillating motor at the rear • one connection forthe line to the tandem pump • one connection forthe line to the hydraulic fluid reservoir. 51 E70 Vertical Dynamics Systems Index Explanation Index Explanation 1 Directional valve 8 Tandem pump line 2 Rear-axle pressure sensor 9 Hydraulic-fluid reservoir line 3 Line 2, front-axle oscillating motor 10 Line 1, rear axle oscillating motor 4 Proportional pressure limiting valve, front axle 11 Line 2, front axle oscillating motor 5 Proportional pressure limiting valve, rear axle 12 Line 1, front axle oscillating motor 6 Front-axle pressure sensor 13 Failsafe valve 7 Switch position recognition sensor Pressure C ontrol Valves There is a pressure control valve on both the front and rear axles. They both adjust the actuation pressures for the front- and rear-axle anti-roll bars. During straight-ahead travel, the pressure regulating valves are in the precurrent-supply (0.35 A) stand-by position; the throttles are open. The fluid is able to flow freely into the tank. As the vehicle enters a bend, the valves are supplied with current. The pressure in the oscillating motors increases rapidly and is regulated to the set point value. Depending on the road speed and rate of lateral acceleration, pressures of up to 160 bar at the front and rear axle may be achieved. The pressure at the front-axle oscillating motor is equal to orgreaterthan the pressure at the rear-axle oscillating motor. 52 E70 Vertical Dynamics Systems Directional Valve The directional valve is electrically actuated. It specifies the direction of the high-pressure fluid (active pressures) and the reservoir fluid for right-hand and left-hand bends. Failsafe Valve The failsafe valve (safety valve) is electrically actuated. The failsafe valve responds in the event of a failure in the power supply or if a fault is detected in the system. In the absence of current, the failsafe valve shuts down the front-axle oscillating motor. The rear-axle oscillating motor is short circuited and simultaneously connected to the tank line. The circulating position limits the system pressure and causes the flow to circulate. Switch-position Recognition Sensor The task of this sensor is to detect the specific position of the directional valve. 2 positions can be detected: • Left-hand control • Right-hand control. Front-axle/Rear-axle Pressure Sensors The pressure sensors are responsible for detecting the front and rear axle anti-roll bar hydraulic pressures. The sensors are mounted on the hydraulic valve block. The pressure sensor offset values are learned by the ARS control unit once, during start-up. 53 E70 Vertical Dynamics Systems Tandem Pump The hydraulic pumps fitted in the E70 were developed with a modular design. Depending on the engine and equipment specification, a suitably dimensioned hydraulic pump is flange-mounted to the engine in the same installation space. Decisive equipment attributes: • Basic steering • Active Steering AS (option 217) • C02 measure (option 1CB) • Adaptive Drive (option 2VA) • Adaptive Drive and Active Steering. The hydraulic pump driven by the engine's poly-V-belt is, on vehicles with Adaptive Drive, invariably a tandem pump, which consists of a radial piston part for ARS and a vane-cell partforthe power steering. Index Explanation Index Explanation A Radial piston pump 3 Steering pressure connection B Vane-cell pump 4 ARS pressure connection 1 Intake connection 5 Input flange 2 Proportional valve 54 E70 Vertical Dynamics Systems Radial Piston Pump (part of the tandem pump) This radial piston pump has 10 pistons set out in two rows and designed fora maximum pressure of 210 bar. When the engine is idling, the pump speed is approximately 750 rpm. Atthis idling speed, the radial piston part delivers a minimum fluid flow rate of approximately 6.75 liters/minute at a pressure of approximately 5 bar. This means that sufficient system dynamics are also guaranteed when the engine is idling. At a pump speed of 1,450 rpm, the maximum fluid flow rate is limited to 13.3 rpm. Vane-cell Pump (part of the tandem pump) This part comprises 10 vane cells and designed for a maximum pressure of 135 bar. The vane-cell part has a characteristic map controlled fluid flow rate of 7-15 liters/minute. The decisive parameters forthe characteristic map are the vehicle's road speed and the steering angle speed. Adaptive Drive and the power steering share the same fluid reservoir and radiator. 55 E70 Vertical Dynamics Systems Fluid Reservoir In the fluid reservoir is a fluid filter and fluid level sensor. The fluid filter cannot be replaced. The screw cap is fitted with a dipstick, which makes it possible to check the fluid level. A "MAX" mark indicates the maximum permissible fluid level, measured at room temperature (20°C). If a dipstick check at room temperature reveals the fluid reservoirto be dry, the reservoir must be topped up with the specified hydraulic fluid. If the lowest edge of the dipstick is still only just wet with hydraulic fluid (3), this is to be construed as the "MIN" mark. Index Explanation Index Explanation 1 Fluid reservoir 3 Hydraulic fluid 2 "MAX" mark 56 E70 Vertical Dynamics Systems Fluid Level Sensor The fluid level sensor detects the fluid level in the fluid reservoir. The fluid level sensor determines whether the fluid level has dropped below a critical minimum level and acti¬ vates a warning message. Normal movements of the fluid in the reservoir are not cause fora message. A mobile float contains a reed contact that converts float movements into an electric signal. The fluid level sensor is fitted to the fluid reservoir. Short/open circuits cannot be detected by the fluid level sensor. A line break is interpreted as a loss of fluid. Fluid level sensor(l) Hydraulic-fluid Cooler The hydraulic-fluid cooler serves to maintain a fluid temperature of <120°C in all hydro-mechanical components under all conditions, although temperatures of < 135°C are acceptable for brief periods. 57 E70 Vertical Dynamics Systems VDC Components VDM Control Unit 1 2 3 4 Index Explanation Index Explanation 1 Comfort Access 4 Vertical Dynamics Management 2 Not for US market 5 Electronic Height Control 3 Park Distance Control Control Strategy The underlying control strategy is known as the "Skyhook regulator"; the name reflects the highest of control objectives: to keep the vehicle body at the same height irrespective of the driving situation (as if the vehicle were suspended from the sky). To achieve this highest of all comfort objectives, the movements of the entire body have to be evaluated. To this end, there is a comprehensive analysis of ride heights and accelerations along the z-axis within the frequency range of between approximately 1 and 3 Hz. 58 E70 Vertical Dynamics Systems The necessary (total) damping force forthis control component will turn out to be com¬ paratively low. To simultaneously ensure that the wheels do not lose contact with the road surface and that optimum contact force is transferred according to the situation, the movement of each individual wheel is evaluated and not just the movement of the entire body. The movements, or excitations, relevant here take place within a frequency range of between approximately 11 and 13 Hz and can therefore be distinguished from the movements of the body. This control component will therefore calculate high damping forces dependent on the vertical movement of the individual wheel. As a matter of principal, these forces may be different at each individual wheel and, for the first time with VDC, can be implemented as such. Furthermore, VDC regulation takes into consideration steering inputs (e.g. transition from straight-ahead travel to cornering) based on the steering angle curve. If VDC detects a rapid increase in the steering angle, the controller infers that the vehicle is entering a bend and can preventively adjust the dampers on the outside of the bend to a harder setting in advance. In this way, VDC is able to support ARS regulation and contributes to a reduction in vehicle rolling movements (of course, this applies also during steady-state circular driving). Moreover, VDC is able to detect the braking applications of the driver based on the brake pressure information supplied by DSC. A high brake pressure normally results in a pitching of the vehicle; VDC counteracts this by adjusting the front dampers to higher damping forces. This also results in an improvement in the front/rear brake force distribution, which in turn reduces the braking distance (by comparison with a vehicle without VDC). The VDC controller adjusts the basic damping force level in accordance with the damp¬ ing program selected by the driver (comfort/sport). Nevertheless, high damping forces are always applied at individual wheels in critical driving situations, e.g. despite the fact that the comfort program is selected. Once the individual control components have been prioritized, a target damping force is output on the FlexRay for each wheel or damper. In addition, the dampers are prescribed a current value forthe steady-state operating point. Display Control The VDM control unit is responsible for evaluating the button on the gear selector lever that the driver uses to select the damping program. Depending on the damping program selected, the VDM control unit issues a request on the PT-CAN to switch the LED in the button on or off (off = comfort, on = sport). 59 E70 Vertical Dynamics Systems Degradation Behavior in the Event of a Fault Depending on the type of fault present, the VDM control unit decides which of three degradation levels must come into effect. • Level 1: Substitute values If, for example, the steering angle signal is unavailable, different variables will be used as a substitute value for cornering detection. The driver receives no failure message. No fault code memory entry is stored. • Level 2: Constant supply of current. The VDM control unit specifies a constant damping force, which is the same for all four wheels ("medium-hard damping"). This leads to a constant supply of current to the valve in the adjusting dampers. A triggering factorforthis degradation level may be a faulty ride-height sensor, for example. The driver receives a failure message. A fault code memory entry is stored. • Level 3: Zero supply of current. If a fault is present in the load circuit, e.g. in the control of a valve, the VDM control unit will select the third degradation level: it tells the dampers that the valve is no longer permitted to be supplied with current. The valve therefore moves into a position that corresponds to a rather hard suspension setting. The driver receives a failure message. A fault code memory entry is stored. From the damping force selected in the degradation levels, it can be seen that it is always the safe condition (hardertuning) that is adopted in the event of a fault (failsafe behavior). Diagnostic Functions The VDM control unit only stores its own faults in its fault memory. Faults with the EDC satellite control units are stored in their own fault memory. In the event of a VDC fault, therefore, it is necessary to check not only the fault memory of the VDM control unit, but of the satellites too. The VDM control unit also functions as a diagnostics gateway between the PT-CAN and VD-FlexRayso that the EDC satellite control units are accessi¬ ble to the tester). Note: The fault memories of the VDM control unit and the EDC satellite control units must be checked in the eventof a VDC system failure. Unlike the EDC-Kinthe E65, it is not necessary to perform straight-ahead calibra¬ tion of the VDC system following replacement of the steering angle sen- sor/SZL. 60 E70 Vertical Dynamics Systems EDC Satellite Control (with damper) This new generation EDC on the E70 is located externally, unlike the EDC system in the E65. The twin-tube gas-pressure damper, EDC satellite control unit and the EDC control valve with wiring as far as the first plug connection form one complete component and can only be replaced in this combination. Index Explanation Index Explanation 1 Twin-tube gas pressure dampers 3 EDC control valve 2 EDC satellite control unit EDC Satellite Control Unit The following functions are implemented in the EDC satellite control unit: • Signal processing:The EDC satellite control units each have one single-axis acceler¬ ation sensor on the control unit board. It is a micro mechanical structural element, which converts accelerations into capacitance changes first and then into an analog voltage signal. This is processed accordingly by the EDC satellite control unit and made available to theVDM control unit via FlexRay. • Actuating functions: Each EDC satellite control unit has a damping characteristic map valid forthis type of damperthat is electronically stored in the form of support points. It is therefore possible to compensate for unavoidable tolerances (variations) arising from manufacture and achieve a higher degree of actuating precision (damp¬ ing force). 61 E70 Vertical Dynamics Systems Note: TheEDC satellite control unit with twin tube gas-pressure damper and EDC control valve can only be replaced as one unit. The vehicle model and installation location (e.g. front left) must be stated when a replacement part is being ordered. • Diagnostic functions Each EDC satellite control unit is compatible with diagnostics and has its own fault memory. Note: The fault memories of the VDM control unit and the EDC satellite con¬ trol units must be checked in the event of a VDC system failure. If the E DC satellite control units do not respond to diagnostics, there may be a fault in the VDM control unit (diagnostic gateway) or FlexRay. A calibration of the ride-height sensors and acceleration sensors must be carried out in the VDM control unit following replacement of an EDC satellite control unit. Twin-tube Gas Pressure Damper Index Explanation 1 Damping force (N) 2 Piston speed (m/s) A Control current = 2 A B Control current = 0.65 A 62 E70 Vertical Dynamics Systems Ride-height Sensor The ride-height sensors are electrically connected directly to the VDM control unit. The mode of signal transfer is analog. Two way or one-way sensors may befitted to the rear axle, depending on the vehicle's equipment level. Two-way sensors deliverthe signal not only to the VDM control unit but also to the EHC control unit. Note: If a new ride- height sensor is being fitted, it must be ensured that only parts with matching part numbers are fitted. In particular, care must be taken not to confuse one-way and two-way sensors (one-way/two-way depends on the equipment level of the vehicle). Two-way sensors bear the marking "doppelt" on the housing. E70 Ride HeightSensors Index Explanation Index Explanation 1 One-way ride height sensor with one output B Adaptive drive with Xenon A Xenon only 63 E70 Vertical Dynamics Systems E70 Ride HeightSensors (Cont.) Index Explanation Index Explanation 1 One-way ride height sensor with one output A Option-EHC and Xenon 2 Two-way ride height sensor with two outputs B Adaptive drive and EHC with Xenon 64 E70 Vertical Dynamics Systems E70 Ride Height Sensor Variants Index Explanation Index Explanation 1 Two-way ride height sensor with two outputs 2 One-way ride height sensor with one output 65 E70 Vertical Dynamics Systems EHC Components EHC Control Unit The EHC control unit is located in a module carrier in the rear of the luggage compart¬ ment on the right-hand side. 1 2 ; 3 , 4 Index Explanation Index Explanation 1 Comfort Access 4 Vertical Dynamics Management 2 Not for US market 5 Electronic Height Control 3 Park Distance Control The EHC control unit receives the following signal information: • Vehicle ride height • Load cutout signals • Terminal 15 ON/OFF • Vehicle speed • Lateral acceleration • "Engine running" signal • Hatch status. The EHC control unit decides on a case-by-case basis whether a control operation is required in orderto compensate for changes in load. It is thus possible to optimally adapt the frequency, specified heights, tolerance thresholds and battery load to the relevant sit¬ uation by means of the control operation. The EHC control unit is fully compatible with diagnostics. 66 E70 Vertical Dynamics Systems Air Supply Unit(LVA) The air supply unit is fitted to the underbody of vehicle by a component carrier level with the front right door. £) vl) ^ L 6 vD Index Explanation Index Explanation 1 Rubber mount 5 Valve block 2 Component carrier 6 Compressor 3 Air drier 7 Air intake 4 Electric motor 67 E70 Vertical Dynamics Systems AirSuspension Index Explanation Index Explanation 1 Rubber gaiter 2 Inner pipe Note: When a new air spring is being fitted, care must be taken to ensure that it is not over-stretched. Otherwise, the retaining ring forthe inner pipe could snap off the rubber gaiter, which could result in damage to the sus¬ pension airbag. Forthis reason, the top of the airspring should be secured to the body first, and only then should it be connected to the axle carrier. Ride-height Sensor The ride-height sensors are electrically connected directly to the EHC control unit. The mode of signal transfer is analog. Two-way or one-way sensors may befitted to the rear axle, depending on the vehicle's equipment level. Two-way sensors deliverthe signal not only to the VDM control unit but also to the EHC control unit. Note: If a new ride- height sensor is being fitted, it must be ensured that only parts with matching part numbers are fitted. In particular, care must be taken not to confuse one-way and two-way sensors (one-way/two-way depends on the equipment level of the vehicle). Two-way sensors bear the marking "doppelt" on the housing. 68 E70 Vertical Dynamics Systems E70 Ride HeightSensors for EHC Index Explanation Index Explanation 1 One-way ride height sensor with one output B Adaptive drive A Standard - Xenon only E70 Ride Height Sensor Variants Index Explanation Index Explanation 1 Two-way ride height sensor with two outputs 2 One-way ride height sensor with one output 69 E70 Vertical Dynamics Systems E70 Ride HeightSensors for EHC (Cont.) Index Explanation Index Explanation 1 One-way ride height sensor with one output A Option-EHC and Xenon 2 Two-way ride height sensor with two outputs B Adaptive drive and EHC with Xenon 70 E70 Vertical Dynamics Systems Service Information If Dynamic Drive fails, DSC can no longer be deactivated or if it is already deactivated it does not switch back on automatically. The connections for all the hydraulic compo¬ nents are designed in different dimensions and lengths so that they cannot be trans¬ posed. A disturbing transmission of noise into the vehicle interior occurs due mainly to the assembly and line connections. The lines must not make contact; they must be routed correctly through the brackets without slack ortension. They are covered by the under¬ body paneling. Steering Angle Calibration After work on the front axle, it is necessary to carry out a steering angle calibration with the Dynamic Drive control unit. The Dynamic Drive system is dependent on the exact zero balance of the steering angle. The maximum deviation tolerance is 1. Precise chassis alignment is a prerequisite. The steering angle calibration must always be carried out on the measuring stand and in accordance with BMW axle alignment guidelines. The zero position is lost each time the Dynamic Drive control unit is flash programmed. A steering angle calibration is required wheneverthe control unit is flash programmed. ARS Initialization The initialization procedure must always be carried out once the system has been opened ora part has been replaced. This also applies afterthe lateral acceleration sensor has been replaced. The following conditions must be guaranteed for calibration of the offset values of the lateral acceleration sensor and the two pressure sensors: • The vehicle must be stand level on all four wheels • The vehicle must be unladen • The engine must be idling • Rest status (doors closed, persons are not allowed in the vehicle). No persons may remain within the vicinity of moving chassis parts during the initialization (both in the works and the workshop). In addition you must ensure that the basic commissioning conditions (temperature range, constant engine speed etc.) are maintained. The ground clearance must not be limited and the doors must not be closed. The arms of the hoist may no longer be situated beneath the car. 71 E70 Vertical Dynamics Systems The commissioning procedure is split into five stages which follow on from each other automatically: 1: direction valve test (from 3 to 3.4 s) Firstthe direction valve is tested by evaluating the signal ofthe SSE. II: low-pressure test (from 3.4 to 4.3 s) The failsafe and direction valves are without power during this stage. Then tests are carried out with pressure control valves with and without power on the front and rear axle.This causes the body to roll. The sides ofthe vehicle must be clear. III: high-pressure testfront axle (from 4.3 to 9.9 s) Pressure of 180 bar is applied to the front-axle oscillating motor. Air in the sys¬ tem, internal leaks and a blocked oscillating motor are detected. IV: high-pressure test rear axle (from 9.9 to 15 s) Pressure of 170 bar is applied to the rear-axle oscillating motor. Air in the system, internal leaks and a blocked oscillating motor are detected. V: pressure control valve test (from 15 to 25 s) The characteristic curves of the front and rear axle are checked (set point/actual- value comparison). Faulty pressure control valves are detected. ARS Bleeding Procedure A bleeding procedure must be carried out using the diagnostic tester if the ARS system was opened hydraulically. The bleeding procedure is performed exclusively by way of the initialization routine of the diagnostic tester and not at the pressure relief valves or at the screw plugs ofthe oscillating motors. If the test still detects air in the system, a short movement trip should be made if necessary. The initialization routine must then be repeated afterthe short trip. In the event of an extreme leak or suspected partial function ofthe pressure relief valves (noticeable by rattling noises in the front end), the pressure relief valves and the pneumat¬ ic lines must be replaced with new components. 72 E70 Vertical Dynamics Systems Diagnostics The following faults can be detected at the components: Component Fault type Fault detection via: Control unit De-energized orfaulty Instrument clusterthrough absence of alive counter, VIN not recognized during authentication, watchdog Pump No Pressure set point/actual-value comparison pressures Directional valve J ammed in "energized" position (spring break, dirt) Direction-valve sensor J ammed in "de-energized" position (line break) Direction valve sensor and current monitoring Pressure control valve FA Open (de-energized, p =pRA) set point/actual-value comparison, pres¬ sure at front axle, current measurement Closed (mechanical fault) (pFA =pmax) set point/actual-value comparison, pressure, front axle RA pressure control valve Open (de-energized) (p =0) set point/actual-value comparison, pres¬ sure, rear axle,and current measurement Closed (mechanical fault) (pRA and pFA = pmax) set point/actual-value comparison, pressure, rear axle, Failsafe valve J ammed open Pre-drive check J ammed closed (line) C urrent measurement Actuator front/rear axle Leaking (no torque) set point/actual-value comparison pressure Blocked set point/actual-value comparison pressure CAN bus Total failure (line disconnected) CAN timeout Steering angle, vCar, aq,Y Implausible or absent Plausibility monitoring and CAN bus sig¬ nal fault detection Sensoraq Total failure (line disconnected) Voltage monitoring Incorrect signal Check plausibility via CAN signals Fluid level sensor No signal (line) Front-axle pressure sensor No signal (line) Voltage monitoring Incorrect signal set point/actual-value comparison, pressure,front axle Rear axle Pressure sensor No signal (line) Voltage monitoring Incorrect signal set point/actual-value comparison, pressure, RA Direction-valve sensor No signal (line) Voltage monitoring Incorrect signal set point/actual-value comparison, pressure, RA 73 E70 Vertical Dynamics Systems Depending on the fault, the system displays one of the following responses. System Shutdown (failsafe status) The following faults result in system shutdown, i.e. all output stages are de-energized: • Fault in the front-axle anti-roll bar • Fault at the front-axle pressure sensor • Fault in the pressure build-up (pump, pressure-limiting valve on the front axle) • Fault in the control unit • VIN is not sent via the C AS / absent / incorrect • Direction valve position fault, faulty SSE • No PT-CAN signal The de-energized failsafe valve shuts off the chambers of the active anti-roll bar. Fluid equalization can only take place by means of internal leakage of the oscillating motor and valve block. The non-return valves in the valve block make it possible to siphon off the fluid to prevent cavitation in the front-axle oscillating motor. The chambers of the rear-axle oscillating motor must not be shutoff. The handling corresponds virtually to that of a conventional vehicle. The crossoverto the failsafe status can also be controlled in the event of extreme manoeuvring. Warning message Cornering stability! Drive slowly around bends Instruction Driving-stability system not functioning, driving stability restricted. No high cornering speeds. Continued driving possible, contact BMW Service immediately The fluid level sensor in the fluid reservoir responds in the event of a fluid loss in the Dynamic Drive hydraulic system or in the steering circuit. The driver is alerted so that damage to the tandem pump caused by continued driving is avoided. Warning message Fluid loss! Pull over carefully, switch off engine Instruction Fluid loss in the chassis and steering systems. Continued driving not possible, contact BMW Service immediately 74 E70 Vertical Dynamics Systems Restricted Control Comfort A lateral acceleration is calculated from the road speed and steering-wheel angle from the CAN signals. This signal is fasterthan the actual lateral acceleration and compensates the time delay of the hydro-mechanical system. In the event of a fault in these two signals, the system responds with a delayed roll compensation. This arises only in the case of extremely quick steering manoeuvres and is barely noticeable in normal cornering manoeuvres. In the event of a faulty lateral acceleration sensor, the lateral acceleration is calculated from the CAN signals only. No impairment of function can be detected by the customer. In the event of a fault in the rear-axle circuit, i.e. a stabilization at the front axle only, the customer notices that the vehicle is subject to larger rolling motions. Agility diminishes at road speeds < 120 km/h. The system also responds if the "failsafe valve jammed open fault" is detected in the Pre-drive check. An electrical fault in the rear-axle pressure sensor may result in minorfailures in roll-angle compensation. To be on the safe side, slightly more stabilizing torque is exerted on the front axle than in normal operation. This can be felt by the driver. Warning message Instruction Cornering stability slightly restricted Chassis stabilization slightly restricted around bends. Continued driving possible, contact BMW Service at next opportunity Restricted System Monitoring Dynamic Drive receives the following sensor signals from the DSC and SZL on the PT-CAN: • Lateral acceleration • Yaw velocity • Road speed • Steering-wheel angle These signals are used to check the lateral acceleration sensor. Drop-out of the engine-speed signal (DME) results in restricted control comfort. In the event of a fault in the lateral acceleration and yaw velocity CAN signals, the system is lacking two items of redundant information. Since this information is used exclusively for checking the other signals, the Dynamic Drive function is preserved with full control comfort. Although no restriction of the Dynamic Drive function exists, the message "Chassis and suspension-control system comfort restricted" is displayed for the driver who is requested to drive to the workshop at the next opportunity. Warning message Instruction Cornering stability slightly restricted Chassis stabilization slightly restricted around bends. Continued driving possible, contact BMW Service at next opportunity 75 E70 Vertical Dynamics Systems A "dynamic" driver will notice the absence of the steering angle signal. The warning messages must be acknowledged by the driver. Each warning message goes out only after it has been acknowledged. Once the cause of the fault has been rectified, the control unit can be returned to full function. There are two reset conditions depending on how fast a fault is to be detected: • All faults that are no longer present are reset with "ignition Off". Forthisto happen, it is necessary to wait until the vehicle has entered sleep mode before switching to "ignition On" again. • Sporadic faults which can mostly be traced back to communication faults in the CAN bus are then automatically reset while the vehicle is moving straight ahead or stationary provided they have only occurred briefly and rarely. In this case, the customer cannot detect the activation while the vehicle is moving or stationary. The associated faults with important additional information are stored in the fault memory. This additional information contains the kilometer reading/mileage at which the fault occurred, whether the fault is currently present and the frequency with which the fault in question has occurred. Thus, when the vehicle is brought into the garage/workshop, it is possible to carry out a specific analysis of the currently present fault and also an analysis of a sporadic fault. Programming It is possible to program the Dynamic Drive control unit. Coding It is possible to code the Dynamic Drive control unit. 76 E70 Vertical Dynamics Systems